国产精品久久二区二区,熟女少妇内射日韩亚洲,久久亚洲国产成人精品无码区,GOGO熟女少妇大尺度

您的瀏覽器版本過低,為保證更佳的瀏覽體驗,請點擊更新高版本瀏覽器

以后再說X

歡迎訪問瑞昌明盛自動化設備有限公司網站!

圖片名

全國訂購熱線:
+86 15270269218E-mail:xiamen2018@foxmail.com

主頁 > 資訊公告 > 產品資訊

產品資訊
產品資訊 行業資訊 工控詢價

IS200DTAIH1ABB IS210DTAOH1AA燃機卡件

作者:xqt 發布時間:2022-07-05 17:30:00 次瀏覽

IS200DTAIH1ABB IS210DTAOH1AA燃機卡件,GE實驗數據EEPROM通電/斷電注意事項MVME147不提供對意外寫入的保護可能在通電或斷電時發生的EEPROM。大多數設備提供一定程度的內部保護。獲得帶有附加“軟件”的“絕對保護”裝置建議使用“保護”。中斷處理程序MC68030可能會被多個電源中斷。所有中斷源是軟件啟用/禁用的。有些人有軟件可編程電平和所有中斷源提供一個矢量在中

IS200DTAIH1ABB IS210DTAOH1AA燃機卡件,GE實驗數據

EEPROM通電/斷電注意事項MVME147不提供對意外寫入的保護可能在通電或斷電時發生的EEPROM。大多數設備提供一定程度的內部保護。獲得帶有附加“軟件”的“絕對保護”裝置建議使用“保護”。中斷處理程序MC68030可能會被多個電源中斷。所有中斷源是軟件啟用/禁用的。有些人有軟件可編程電平和所有中斷源提供一個矢量在中斷確認周期內。PCC芯片解碼MC68030地址總線和功能確定中斷周期何時進行的代碼。

IS200DTAIH1ABB IS210DTAOH1AA -4.jpg

IS200DTAIH1ABB IS210DTAOH1AA -3.jpg

IS200DTAIH1ABB IS210DTAOH1AA -2.jpg

IS200DTAIH1ABB IS210DTAOH1AA燃機卡件當PCC在其水平上檢測中斷確認周期中斷,它傳遞狀態/ID向量。否則向VMEchip生成中斷確認輸出信號。

當VMEchip在信號中檢測到中斷確認時從PCC,它在該級別中斷,它通過一個狀態/ID向量。否則,它將請求VMEbus的主控權(如果沒有主控權),并驅動VMEbus信號啟動中斷確認周期的線路。打斷從機返回狀態/ID向量。在一個級別內,來自PCC的中斷具有最高的VMEchip和VMEbus中斷后的優先級最低優先級。前面板開關和指示燈MVME147的前面板上有兩個開關。這個開關復位并中止。重置開關重置所有車載設備并驅動系統重置*如果MVME147是系統控制器。復位開關可能是被軟件禁用。請參閱復位和中止開關本章第節。啟用時,中止開關生成7級中斷。它是通常用于中止程序執行并返回到調試器。中止開關可以通過軟件禁用。提到

本章中的重置和中止開關部分。

MVME147的前面板上有四個LED指示燈。


指示器為RUN、STATUS、FAIL和SCON。


? 當MC68030地址選通(AS*)引腳低時,RUN點亮。


? 當MC68030狀態*引腳低時,狀態點亮。


? 當在中設置Board FAIL(BRDFAIL)位時,FAIL點亮


VMEchip或PCC中出現看門狗超時時。


? 當MVME147是VMEbus系統時,SCON點亮


控制器(由跳線J3選擇)。

EEPROM Power-Up/Power-Down Considerations

The MVME147 provides no protection against inadvertent writes to

EEPROM that might happen at power-up or power-down time.

Most devices provide some level of internal protection. To gain

“absolute protection” devices with additional “software

protection” are recommended.

Interrupt Handler

The MC68030 may be interrupted by many sources. All interrupt

sources are software enabled/disabled. Some have software

programmable levels and all interrupt sources supply a vector

during an interrupt acknowledge cycle.

The PCC chip decodes the MC68030 address bus and function

codes to determine when an interrupt cycle is in progress. When the

PCC detects an interrupt acknowledge cycle at the level it is

interrupting on, it passes a status/ID vector. Otherwise, it

generates an interrupt acknowledge out signal to the VMEchip.

When the VMEchip detects an interrupt acknowledge in signal

from the PCC and it is interrupting at that level, it passes a

status/ID vector. Otherwise, it requests mastership of the VMEbus

(if it does not have mastership), and it drives the VMEbus signal

lines to initiate an interrupt acknowledge cycle. The interrupting

slave returns a status/ID vector.

Within a level, the interrupts from the PCC have the highest

priority followed by the VMEchip and the VMEbus interrupts have

the lowest priority. Front Panel Switches and Indicators

There are two switches on the front panel of the MVME147. The

switches are RESET and ABORT.

The RESET switch resets all onboard devices and drives SYSRESET*

if the MVME147 is the system controller. The RESET switch may be

disabled by software. Refer to the RESET and ABORT Switches

section in this chapter.

The ABORT switch generates a Level 7 interrupt when enabled. It is

normally used to abort program execution and return to the

debugger. The ABORT switch may be disabled by software. Refer to

the RESET and ABORT Switches section in this chapter.

There are four LED indicators on the front panel of the MVME147.

The indicators are RUN, STATUS, FAIL, and SCON.

? RUN is lit when the MC68030 Address Strobe (AS*) pin is low.

? STATUS is lit when the MC68030 STATUS* pin is low.

? FAIL is lit when the Board Fail (BRDFAIL) bit is set in the

VMEchip or when watchdog time-out occurs in the PCC.

? SCON is lit when the MVME147 is the VMEbus system

controller (selected by jumper J3).


圖片名 客服

在線客服 客服一號