WOODWARD 8200-1300調速器9907-164的升級型號

在以前的固件版本中，非致命應用程序的故障條目提供的錯誤（例如，引用超出范圍）數字識別導致錯誤的邏輯塊的信息。然而用戶無法將數字信息與塊的名稱。

新固件包括前12個字符故障條目中的塊名稱。在5.00版或更高版本中，如果嘗試下載C塊

如果包含未定義的符號，則下載將失敗。

機器版將在反饋區顯示以下消息：錯誤8097：控制器錯誤–控制器中止了請求[0x05][0xFF]在5.00版之前，包含未定義符號的C塊可以成功下載，但如果它們被執行，CPU將轉換到停止/暫停模式。

（5.0版或更高版本）“設置輸入緩沖功能”將始終分配一個包含2049字節的緩沖區。這比先前的PACSystems版本。

傳輸列表驗證與不兼容版本2.0x CRE020

使用CPU固件版本2.0x生成的冗余傳輸列表或更早版本與3.80版及更高版本的傳輸不兼容列表。

運行2.0x版的冗余控制器不會能夠與運行3.80版或更高版本的固件。

以下限制適用于PACSystems RX7i機架：

? 基本模塊必須位于不低于插槽4的插槽中。

? 擴展器模塊必須位于不高于插槽11的插槽中。

? 擴展器模塊不得位于低于底座的插槽中單元由于這些限制，以及90-70模塊占用PACSystems RX7i機架中有兩個插槽，最多三個可以使用擴展器。

（插槽4中的基座，插槽6、8和中的擴展器10或插槽5中的底座，插槽7、9和11中的擴展器。）請注意這些限制不適用于串聯模擬擴展模塊90-70擴展機架。

Genius總線控制器限制以下限制適用于PACSystems RX7i中的GBC：? 最小CPU掃描時間將按所需時間進行選通GBC更新其輸出并收集其輸入+500微秒。

要獲得較小的掃描時間，請使用SUSIO功能塊或將GBC放置在具有非默認特征的掃描集中。

? 如果%W參考地址用于COMMREQ狀態或返回數據，它必須在%W00001-%W65536范圍內。

? 存儲或清除包含兩個GBC的硬件配置連接到同一Genius網絡可能會導致設備丟失其中一個GBC的故障。這是由GBC清算引起的他們的SBA異步。用戶可以安全地忽略損失設備故障

In previous firmware versions, the fault entry for a non-fatal application

fault (for example, reference-out-of-range) provided numeric

information to identify the logic block causing the error. However, the

user did not have a way to correlate the numeric information with the

name of the block. The new firmware includes the first 12 characters

of the block name in the fault entry.In Release 5.00 or later, if an attempt is made to download a C block

containing undefined symbols, the download will fail. Machine Edition

will display the following message in the Feedback Zone: Error 8097:

Controller Error – Controller aborted the request [0x05][0xFF]

Prior to Release 5.00, C blocks containing undefined symbols could be

successfully downloaded, but if they were executed the CPU would

transition to Stop/Halt mode.(Release 5.0 or later) The "Set Up Input Buffer Function" will always

allocate a buffer containing 2049 bytes. This is one byte more than

previous PACSystems releases.

Transfer list validation not compatible with

Release 2.0x CRE020

Redundant transfer lists generated using CPU Firmware release 2.0x

or earlier are not compatible with the release 3.80 and later transfer

lists. Redundant controllers that are running release 2.0x will not be

able to synchronize with controllers that are running release 3.80 or

later firmware.The following restrictions apply to Analog Expansion Modules in a

PACSystems RX7i rack:

? The base module must be in a slot no lower than Slot 4.

? The expander module must be in a slot no higher than Slot 11.

? No expander module may be in a slot lower than the base

module.

Because of these restrictions, and because the 90-70 modules occupy

two slots in the PACSystems RX7i rack, a maximum of three

expanders are possible. (Base in Slot 4, Expanders in Slots 6, 8, and

10 or Base in Slot 5, Expanders in Slots 7, 9, and 11.) Please note that

these restrictions do not apply to Analog Expansion Modules in Series

90-70 Expansion Racks.

Genius Bus Controller restrictions The following restrictions apply to GBCs in PACSystems RX7i:

? The minimum CPU sweep time will be gated by the time it takes

the GBC to refresh its outputs and collect its inputs + 500

microseconds. To obtain a smaller sweep time, use the SUSIO

function block or place the GBCs in a scan set that has nondefault characteristics.

? If a %W reference address is used for COMMREQ status or return

data, it must be in the range %W00001 - %W65536.

? Storing or clearing a hardware configuration containing two GBCs

attached to the same Genius network may cause a Loss of Device

fault for one of the GBCs. This is caused by the GBCs clearing

their SBAs asynchronously. The user can safely ignore the Loss

of Device fault.