論GDC780BE21 3BHE004468R0021控制器的優勢

步驟1（4）退出：當三相kvar值小于或等于該設定點中設定的值，分配給該步驟的輸出繼電器將斷電。

由于過補償是可能的，所以可以將漏失值設置為負VAR。

?步驟1（4）拾取延遲：該步驟將在設定點中設置的延遲達到假設滿足所有其他條件，則經過。

注：該延遲設置將在系統穩定時間設置后開始倒計時已經過去了。

?步驟1（4）禁用時間：當步驟關閉時，直到此設定點中設置的時間已過。這允許電容器在之前放電再次通電。

?系統穩定時間：執行任何動作時（打開/關閉步驟或檢測到低電壓），必須允許系統在本中設置的時間內穩定設置點，然后才能執行任何進一步的操作。這一時間是必要的系統穩定，無需電容器嘗試充電

?低電壓電平

當系統電壓（平均三相電壓）時等于或小于該設定值時，所有步驟均關閉。恢復后（三相電壓大于該設定點）系統中設定的時間在執行任何動作之前，穩定時間設定點必須已過。如果不需要此功能，請將其設置為“關閉”。

?低電壓檢測延遲：在某些情況下，出現噪聲或尖峰線路可能不希望立即檢測低電壓，因此設定點可用于延遲檢測，直到電壓確實較低。

?步進優先級：步進優先級設定點決定了步進的順序允許在多個條件可能滿足的情況下打開步驟。因此，具有最高優先級的步驟將首先通電。如果步驟最高優先級已通電，第二高優先級的步驟將為使用等等。步驟優先級從最高到最低（從左到右）設置為：查看此設定點。例如，“1,2,3,4”表示步驟1具有最高優先級和步驟4具有最低優先級。請注意，只允許打開一個步驟一次打開或關閉。

A、 1.3實際值以下消息已添加到PQMII實際值結構中：適應這種修改。消息位于“實際值”頁面中狀態?MOD 506實際值。路徑：實際值214?A2狀態214216;MOD 506實際值

STEP 1(4) DROPOUT: When the three-phase kvar value becomes less than or equal to

the value set in this setpoint the output relay assigned to the STEP will de-energize.

Since over compensation is possible, the dropout value can be set to negative vars.

? STEP 1(4) PICKUP DELAY: The STEP will turn on after the delay set in this setpoint has

elapsed assuming all other conditions have been met.

Note This delay setting will start counting down once the SYSTEM STABILIZATION TIME setting

has elapsed.

? STEP 1(4) DISABLE TIME: When STEP turns off, it is not allowed to turn back on until the

time set in this setpoint has elapsed. This allows the capacitors to discharge before

being re-energized again.

? SYSTEM STABILIZATION TIME: When any action is performed (turning STEPS on/off or

low voltage is detected), the system must be allowed to stabilize for the time set in this

setpoint before any further actions can be performed. This time is necessary to allow

the system to stabilize without the capacitors trying to recharge

? LOW VOLTAGE LEVEL: When the system voltage (average three-phase voltage)

becomes equal to or less than this setpoint, all STEPS are turned off. Upon recovery

(three-phase voltage is greater than this setpoint) the time set in the SYSTEM

STABILIZATION TIME setpoint must have elapsed before any actions will be performed. If

this feature is not required, set it to “Off”.

? LOW VOLTAGE DETECT DELAY: In some cases where noise or spikes are present on

the line it may not be desirable to detect low voltage right away, therefore, this

setpoint can be used to delay the detection until voltage is definitely low.

? STEP PRIORITY: The STEP PRIORITY setpoint determines the sequence the STEPS are

allowed to turn on in a case where the condition may be satisfied by more than one

STEP. Therefore, the STEP with the highest priority will be energized first. If the STEP

with highest priority is already energized, the STEP with second highest priority will be

used, and so forth. The STEP priority is set from highest to lowest (left to right) when

viewing this setpoint. For example, “1,2,3,4” signifies that STEP 1 has the highest

priority and STEP 4 has the lowest priority. Note that only one STEP is allowed to turn

on or off at a time.

A.1.3 Actual Values

The following messages have been added to the PQMII actual values structure to

accommodate this modification. The messages are located in actual values page

A2 STATUS ?? MOD 506 ACTUAL VALUES.

PATH: ACTUAL VALUES ?? A2 STATUS ?? MOD 506 ACTUAL VALUES