HONEYWELL 51202329-606連接電纜,51202329-606中文PDF用戶手冊
數據總線結構MVME162上的本地數據總線是基于在MC68040總線上，支持突發傳輸和偵聽。這個各種本地總線主設備和從設備使用本地總線進行通信。本地總線由優先級類型仲裁器和本地總線的優先級進行仲裁總線主機從高到低依次為：82596CA LAN、NCR 53C710 SCSI、，VMEbus和MPU。一般來說，任何主設備都可以訪問任何從設備；
HONEYWELL 51202329-606連接電纜然而，并非所有組合都通過了常識測試。請參閱MVME162嵌入式控制器程序員參考指南和用戶的每個設備確定其端口大小、數據總線連接和任何訪問設備時適用的限制。MC68040/MC68LC040微處理器MVME162配備MC68040或MC68LC040微處理器。MC68040/MC68LC040具有片上指令和數據緩存；這個MC68040還提供浮點協處理器。參見M68040微處理器用戶手冊了解更多信息。EPROM和閃存MVME162實現包括四個2-Mbit閃存設備在256Kbit x 8配置中。EPROM位置為標準JEDEC 32-引腳PLCC能夠達到4Mbit密度（128 Kbit x 8；256 Kbit x 8；512 Kbit x 8；1 Mbit x8）組織為512Kbit x 8設備。跳線設置（GPIO3，引腳9-J22上的10）允許從閃存（GPIO3）中提取重置代碼安裝）或從EPROM（GPIO3已卸下）。SRAMMVME162在單個內存中提供512KB的32位寬板載靜態RAM具有車載電池備份的非交錯架構。最壞的情況電池保護所用時間為200天。SRAM的詳細信息性能可在中的SRAM內存控制器部分中找到MVME162嵌入式控制器中的MCchip編程模型程序員參考指南。SRAM陣列沒有奇偶校驗保護。MVME162 SRAM的電池備份功能由Dallas提供DS1210S支持主電源和輔助電源的設備。在如果主板電源出現故障，DS1210將檢查電源和切換到電壓較高的電源。如果備用電源的電壓低于兩伏，則DS1210會阻塞第二個存儲周期；這使軟件能夠向避免數據丟失。因為第二次訪問可能會在通電期間被阻止失敗時，軟件應在依賴數據之前至少進行兩次訪問。MVME162提供跳線（在J20上），允許DS1210通過引腳連接到VMEbus+5V STDB或連接到車載電池。例如，主系統備份源可能是蓄電池通過引腳和二次電源連接到VMEbus+5V STDB可能是車載電池。如果系統電源出現故障或電路板從機箱中卸下后，車載電池將接管。
MC68040/MC68LC040 MPU The MVME162 is equipped with an MC68040 or MC68LC040 microprocessor. The MC68040/MC68LC040 have on-chip instruction and data caches; the MC68040 also provides a floating-point coprocessor. Refer to the M68040 Microprocessor User’s Manual for more information. EPROM and Flash Memory The MVME162 implementation includes four 2-Mbit Flash devices organized in a 256Kbit x 8 configuration. The EPROM location is a standard JEDEC 32- pin PLCC capable of 4 Mbit densities (128 Kbit x 8; 256 Kbit X 8; 512 Kbit x 8; 1 Mbit x8) organized as a 512Kbit x 8 device. A jumper setting (GPIO3, pins 9- 10 on J22) allows reset code to be fetched either from Flash memory (GPIO3 installed) or from the EPROM (GPIO3 removed). SRAM The MVME162 provides 512KB of 32-bit-wide onboard static RAM in a single non-interleaved architecture with onboard battery backup. The worst case elapsed time for battery protection is 200 days. Specifics on SRAM performance can be found in the section on the SRAM Memory Controller in the MCchip Programming Model in the MVME162 Embedded Controller Programmer’s Reference Guide. The SRAM arrays are not parity protected. The battery backup function for the MVME162 SRAM is provided by a Dallas DS1210S device that supports primary and secondary power sources. In the event of a main board power failure, the DS1210S checks power sources and switches to the source with the higher voltage. If the voltage of the backup source is lower than two volts, the DS1210S blocks the second memory cycle; this allows software to provide an early warning to avoid data loss. Because the second access may be blocked during a power failure, software should do at least two accesses before relying on the data. The MVME162 provides jumpers (on J20) that allow either power source of the DS1210S to be connected to the VMEbus +5V STDBY pin or to one cell of the onboard battery. For example, the primary system backup source may be a battery connected to the VMEbus +5V STDBY pin and the secondary source may be the onboard battery. If the system source should fail or the board is removed from the chassis, the onboard battery takes over.
