国产精品久久二区二区,熟女少妇内射日韩亚洲,久久亚洲国产成人精品无码区,GOGO熟女少妇大尺度

您的瀏覽器版本過低,為保證更佳的瀏覽體驗,請點擊更新高版本瀏覽器

以后再說X

歡迎訪問瑞昌明盛自動化設備有限公司網站!

圖片名

全國訂購熱線:
+86 15270269218E-mail:xiamen2018@foxmail.com

主頁 > 資訊公告 > 產品資訊

產品資訊
產品資訊 行業資訊 工控詢價

PFEA112-65 3BSE050091R65控制器

作者:xqt 發布時間:2022-07-05 15:23:35 次瀏覽

PFEA112-65 3BSE050091R65控制器,ABB英文使用說明安裝遠程開關和電纜后,MVME147可以通過遠程開關或前面板重置開關重置。故障指示器(DS1)紅色故障指示燈DS1指示BRDFAIL位的狀態VMEchip。當設置BRDFAIL位或當PCC中出現看門狗超時時。此外,如果故障指示燈為未設置VMEchip中的lit和SYSFAIL抑制位,MVME147VMEbus上的驅動器SYS

PFEA112-65 3BSE050091R65控制器,ABB英文使用說明

安裝遠程開關和電纜后,MVME147可以通過遠程開關或前面板重置開關重置。故障指示器(DS1)紅色故障指示燈DS1指示BRDFAIL位的狀態VMEchip。當設置BRDFAIL位或當PCC中出現看門狗超時時。此外,如果故障指示燈為未設置VMEchip中的lit和SYSFAIL抑制位,MVME147VMEbus上的驅動器SYSFAIL。狀態指示器(DS2)每當MC68030啟動時,黃色狀態LED DS2亮起狀態*引腳低。

PFEA112-65 3BSE050091R65 -5.jpg

PFEA112-65 3BSE050091R65 -4.jpg

PFEA112-65 3BSE050091R65 -3.jpg

PFEA112-65 3BSE050091R65 -1.jpg

PFEA112-65 3BSE050091R65控制器當黃色LED完全點亮時,處理器已停止。綠色運行指示燈DS3連接至MC68030地址選通(AS*)信號,指示微處理器正在執行總線周期SCON指示器(DS4)當MVME147為VMEbus系統控制器。表3-1。前面板指示燈和MVME147狀態(綠色)MVME147狀態off off off模塊未通電,或MPU不是當前本地總線主節點。關閉-關閉-打開MPU正在等待一個循環完成。off ON(亮)off MPU暫停。off ON(正常)off MPU僅在其片上緩存中執行。正常運行時關閉打開。開-關-關MPU不是當前的本地總線主機,并且未執行芯片緩存不足。此外,[BRDFAIL]尚未重置后清除或已由軟件設置。ON off ON[BRDFAIL]自重置后未清除或已設置通過軟件。此外,MPU正在等待一個周期的完成。ON ON(亮)off MPU暫停,[BRDFAIL]此后未被清除重置或已由軟件設置。ON ON(normal)off[BRDFAIL]自重置后未清除或已設置通過軟件。此外,MPU在片上緩存外執行只有ON ON ON[BRDFAIL]自重置后未清除或已設置通過軟件。

When the remote switch and cable is installed, the MVME147 can

be reset by the remote switch or by the front panel RESET switch.

FAIL Indicator (DS1)

The red FAIL LED, DS1, indicates the status of the BRDFAIL bit in

the VMEchip. The FAIL LED lights when the BRDFAIL bit is set or

when watchdog time-out occurs in the PCC. Also, if the FAIL LED is

lit and SYSFAIL inhibit bit in the VMEchip is not set, the MVME147

drives SYSFAIL on the VMEbus.

STATUS Indicator (DS2)

The yellow STATUS LED, DS2, lights whenever the MC68030

STATUS* pin is low. When the yellow LED is fully lit, the processor

has halted.The green RUN LED, DS3, is connected to the MC68030 address

strobe (AS*) signal and indicates that the MPU is executing a bus

cycle.

SCON Indicator (DS4)

The green SCON LED, DS4, lights when the MVME147 is the

VMEbus system controller.

Table 3-1. Front Panel Indicators and MVME147 Status

(Green) MVME147 Status

off off off No power is applied to the module, or the MPU is not the

current local bus master.

off off ON MPU is waiting for a cycle to complete.

off ON (bright) off MPU is halted.

off ON (normal) off MPU is executing out of its onchip cache only.

off ON ON Normal operation.

ON off off MPU is not current local bus master and is not executing

out of onchip cache. Also, [BRDFAIL] has not been

cleared since reset or has been set by software.

ON off ON [BRDFAIL] has not been cleared since reset or has been set

by software. Also, MPU is waiting for a cycle to complete.

ON ON (bright) off MPU is halted and [BRDFAIL] has not been cleared since

reset or has been set by software.

ON ON (normal) off [BRDFAIL] has not been cleared since reset or has been set

by software. Also, MPU is executing out of onchip cache

only.

ON ON ON [BRDFAIL] has not been cleared since reset or has been set

by software.


圖片名 客服

在線客服 客服一號