HIMA F7553處理器模塊,F7553控制器確定主模塊為特定從模塊報告的值，如果主設備和從設備之間的通信中斷。選擇是最后一個狀態（默認）和清除。從機狀態故障表條目如果設置為True（默認），則從通信狀態事件（丟失和重新建立）為報告為故障表條目。如果設置為False，則不會將從屬狀態事件報告給故障表。如果設置為True，則從設備和主設備的名稱和描述將發送到PLC上傳時不要恢復默認值。
HIMA F7553處理器模塊如果設置為False，則名稱和描述未下載到PLC，并在從PLC。注意：下載名稱和說明可能會占用PLC中太多內存。建議：參數保持設置為False（默認）。名稱和描述僅供參考。從中省略它們下載不會影響系統操作。下載GSD文件確定是否可以從已下載配置。如果將此參數設置為False（默認），則不會將GSD文件下載到PLC。后續上載操作是通用的。如果設置為True，則網絡配置所需的GSD文件將發送到PLC。后續上載操作為完全上載。完全上傳——包含PBM200的硬件配置的完全上傳具有以下特點：如果下載時Download GSD Files設置為True，則發生。您擁有完整的配置功能，包括添加從屬和添加新的模塊到現有從屬設備。工具箱中填充了上傳配置中的GSD文件，允許您向配置中添加更多現有從屬設備。文本字段（如描述）的下載/上載由下載名稱/描述參數。通用上傳——包含PBM200的硬件配置的通用上傳具有以下特點：如果下載時Download GSD Files設置為False（默認值），則發生。如果項目是從PLC上傳的，并且GSD文件在工具箱中，重建網絡。如果用于構建網絡的GSD文件是工具箱中不存在網絡，但無法重建新模塊添加到奴隸。工具箱中沒有GSD文件的現有從機已生成通用的您不能在通用從屬服務器下添加或刪除模塊。可以在通用從機上執行以下操作：-更改其站號。-在十六進制模式下編輯其參數。-刪除從屬。可以從工具箱中的GSD文件中添加新的、功能齊全的從機。
Determines the values that the master module reports for a particular slave if
communications between master and slave are lost. Choices are Hold Last
State (default) and Clear.
Slave Status Fault Table
Entries
If set to True (default), slave communications status events (loss and re-establish) are
reported as fault table entries. If set to False, slave status events are not reported to the
fault table.
Download
Names/Descriptions
If set to True, names and descriptions for the slaves and the master are sent to the PLC
and do not revert to default upon uploading. If set to False, the names and descriptions
are not downloaded to the PLC and revert to the default values upon uploading from the
PLC.
Note: Downloading names and descriptions may use too much memory in the PLC. It is recommended that this
parameter remain set to False (Default). Names and descriptions are a convenience only. Omitting them from
the download does not affect system operation.
Download GSD Files Determines whether a Full Upload or Generic Upload can be performed from the
downloaded configuration.
If you set this parameter to False (default), GSD files are not downloaded to the PLC.
Subsequent upload operations are Generic.
If set to True, the GSD files required by the network configuration are sent to the PLC.
Subsequent upload operations are Full uploads.
Full Upload -- A full upload of a hardware configuration containing a PBM200 has the
following characteristics:
Occurs if Download GSD Files is set to True on download.
You have full configuration capability, including adding slaves and adding new
