REXROTH CDB01.1C-ET-EN1-EN1-NNN-NNN-L2-S-NN-FW驅動控制器
1.產 品 資 料 介 紹：
中文資料：
CDB01.1C -ET-EN1-EN1-NNN-NNN-L2-S-NN-FW由Rexroth Indramat 公司生產。它是一個控制部分，安裝在驅動控制器的功率部分中。驅動控制器用于工業機器人、機床、印刷機和食品加工機等應用。該類型使用DC 24V電壓供電，最大脈沖寬度為110 ms，浪涌電流為4.5 A，DC 24V時功耗為8 W。為了實現精確連接，它配備了多種附件，例如光纖電纜連接、信號電平轉換器和用于編碼器仿真的信號電平轉換器。
CDB01.1C -ET-EN1-EN1-NNN-NNN-L2-S-NN-FW應在以下環境條件下運行，其中包括海拔高度1000 米、允許濕度 95% 和 25g/m3絕對濕度。該部分可單獨交付，應由Rexroth Indramat培訓的人員安裝和拆卸。確保安裝和拆卸不超過 20 次，因為這會增加損壞的風險。它是一個雙軸控制部分，具有可配置選項，配備一個配置插槽安全技術，并具有 7-11 個數字輸入。CDB01.1C-ET-EN1-EN1-NNN-NNN-L2-S-NN-FW的開關頻率范圍為 2 kHz 和 4 kHz 到 16 kHz。
此控制部分編碼器 HSF/RSF 選項、MultiEthernet 主站通信、標準控制部分和安全扭矩 OFF 安全選項。控制面板不適合熱插拔，應在驅動控制器投入運行時插入。它允許您設置驅動器地址、建立位置數據參考和設置模擬輸出。CDB01.1C -ET-EN1-EN1-NNN-NNN-L2-S-NN-FW應具有充足的氣流以實現最佳冷卻效果。
英文資料：
CDB01.1C - ET-EN1-EN1-NNNN-L2-S-NN-FW is produced by Rexroth Indramat. It is a control section installed in the power section of the drive controller. Drive controllers are used in applications such as industrial robots, machine tools, printing machines, and food processing machines. This type uses a DC 24V voltage supply, with a maximum pulse width of 110 ms, a surge current of 4.5 A, and a power consumption of 8 W at DC 24V. To achieve precise connection, it is equipped with various accessories, such as fiber optic cable connections, signal level converters, and signal level converters for encoder simulation.
CDB01.1C - ET-EN1-EN1-NNNN-L2-S-NN-FW should operate under the following environmental conditions, including an altitude of 1000 meters, allowable humidity of 95%, and absolute humidity of 25g/m3. This part can be delivered separately and should be installed and disassembled by personnel trained by Rexroth Indramat. Ensure that installation and disassembly do not exceed 20 times, as this increases the risk of damage. It is a dual axis control section with configurable options, equipped with a configuration slot security technology, and has 7-11 digital inputs. The switching frequency range of CDB01.1C-ET-EN1-EN1-NNNN-NNN-L2-S-NN-FW is 2 kHz and 4 kHz to 16 kHz.
This control section includes encoder HSF/RSF option, MultiEthernet master station communication, standard control section, and safety torque OFF safety option. The control panel is not suitable for hot swapping and should be inserted when the drive controller is put into operation. It allows you to set drive addresses, establish location data references, and set analog outputs. CDB01.1C - ET-EN1-EN1-NNNN-L2-S-NN-FW should have sufficient airflow to achieve optimal cooling effect.
2.產 品 展 示
3.主 營 品 牌
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.g2813.cn
