WOODWARD 5501-367數字量輸入卡件
1.產 品 介 紹
品牌：WOODWARD
型號說明：WOODWARD 5501-367數字量輸入卡件
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
WOODWARD 5501-367基板電纜連接：a.將電源線連接到兩個CPU，將電源監控信號從SS8xx連接到螺絲端子SA和SB。將控制網絡電纜連接到CN1（單總線連接）或CN1+CN2（冗余總線連接）。控制網絡連接到兩個CPU。c.使用主CPU的電纜TK212將控制生成器連接到COM4（如果需要更改IP地址等）。否則，將控制生成器與控制網絡連接。將光學模塊總線連接到處理器單元上的光學觸點（參見第32頁的圖2和第131頁的圖40）。S800 I/O文檔中提供了有關光纜選擇和光纜長度的信息。請注意，必須使用RCU鏈接電纜TK851WOODWARD 5501-367，不能用類似的電纜代替。使用另一根電纜將禁用CB和操作員站中CPU的識別。當以單一配置運行時，RCU鏈路電纜TK851可能暫時用于執行終端插頭的功能。連接到標有“UPPER”的RCU鏈接電纜連接器的CPU將在控制生成器和操作員站中定義為“UPPER”。標記與CPU的物理位置無關。任何CPU都可以成為主CPU。兩個CPU應由同一電源供電（單電源或冗余電源）。有關冗余電源，請參見第140頁的圖46。與光模塊總線的連接與S800 I/O中處理器單元和FCI的連接相同WOODWARD 5501-367
Baseplates cable connections: a. Connect the power leads to both CPUs and the power supervision signals from SS8xx to screw terminals SA and SB Connect the Control Network cables to CN1 (single bus connection) or CN1 + CN2 (redundant bus connection).WOODWARD 5501-367 The Control Network is connected to both CPUs. c. Connect the Control Builder to COM4 with cable TK212 of the Primary CPU (if required for changing an IP address etc.). Otherwise connect the Control Builder to the Control Network.Connect the optical ModuleBus to the optical contacts on the processor units (see Figure 2 on page 32 and Figure 40 on page 131). Information regarding optical cable selection and cable length is provided in the S800 I/O documentation. Note that the RCU Link Cable TK851 must be used and can not be replaced by a similar cable. WOODWARD 5501-367Using another cable will disable the identification of the CPUs in the CB and Operator Station. When running in single configuration the RCU Link Cable TK851 might temporarily be used to perform the function of a termination plug. The CPU connected to the RCU Link Cable connector marked “UPPER” will be defined as “UPPER” in the Control Builder and Operator Station. The marking has no relevance to the physical placement of the CPUs. Any CPU can become the Primary CPU. Both CPUs should be powered from the same supply (single or redundant). For redundant power supply, see Figure 46 on page 140. Connection to the optical ModuleBus is identical to that for the processor unit and for the FCI in S800 I/OWOODWARD 5501-367
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.g2813.cn
