REXROTH MSK040C-0600-NN-M1-UG0-NNNN伺服電機
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH MSK040C-0600-NN-M1-UG0-NNNN伺服電機
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH MSK040C-0600-NN-M1-UG0-NNNN如果嘗試的網絡操作失敗，則網絡I/O錯誤代碼162Bug將返回錯誤代碼。多處理器支持MVME162FX控制器的雙端口RAM功能使共享RAM可用于遠程處理器和本地處理器。這可以通過以下兩種方法之一完成。任何一種方法都可以通過ENV命令啟用/禁用，作為其遠程啟動開關方法（參見第5章）。多處理器控制寄存器（MPCR）REXROTH MSK040C-0600-NN-M1-UG0-NNNN方法遠程處理器可以通過使用多處理器控制暫存器（MPCR，Multiprocessor Control Register）發出遠程GO命令，在本地MVME162FX雙端口RAM中啟動程序執行。MPCR位于共享RAM位置，與調試器加載它的基地址相距800美元，它包含用于控制處理器之間通信的兩個長字之一。MPCR內容組織如下：MPCR中存儲的狀態代碼有兩種類型：? 返回的狀態（從監視器）? 狀態設置（由總線主機設置）監視器可能返回的狀態代碼為：等待。初始化尚未完成。REXROTH MSK040C-0600-NN-M1-UG0-NNNN
Network I/O Error Codes 162Bug returns an error code if an attempted network operation is unsuccessful. Multiprocessor REXROTH MSK040C-0600-NN-M1-UG0-NNNNSupport The MVME162FX controller’s dual-port RAM feature makes the shared RAM available to remote processors as well as to the local processor. This can be done by either of the following two methods. Either method can be enabled/disabled by the ENV command as its Remote Start Switch Method (refer to Chapter 5). Multiprocessor Control Register (MPCR) Method A remote processor can initiate program execution in the local MVME162FX dual-port RAM by issuing a remote GO command using the Multiprocessor Control Register (MPCR). The MPCR, located at shared RAM location of $800 offset from the base address the debugger loads it at, contains one of two longwords used to control communication between processors. The MPCR contents are organized as follows: The status codes stored in the MPCR are of two types: ? Status returned (from the monitor) ? Status set (by the bus master) The status codes that may be returned from the monitor are:Wait. Initialization not yet complete.REXROTH MSK040C-0600-NN-M1-UG0-NNNN
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.g2813.cn
