REXROTH HMV01.1E-W0030-A-07-NNNN驅動模塊
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH HMV01.1E-W0030-A-07-NNNN驅動模塊
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
注意：如果您使用的是PROM版本的162Bug（例如，在noVMEbus中，REXROTH HMV01.1E-W0030-A-07-NNNN控制器的空白閃存版本），并且您希望在后續會話中從閃存而不是PROM執行調試器，請確保162Bug處于Board Mode（板模式），并使用PFLASH命令將PROM內容復制到閃存中，REXROTH HMV01.1E-W0030-A-07-NNNN如下所示：然后在J22引腳9和10處重新安裝跳線。（162Bug始終從內存位置FF800000執行；J22的狀態決定該位置是在PROM還是閃存中。）Autoboot Autoboot是一個包含在162Bug flash/PROM中的軟件例程，為啟動操作系統提供獨立機制。此自動引導例程按指定順序自動掃描控制器和設備，直到找到包含引導介質的有效可引導設備或列表用盡。如果找到有效的可引導設備，則啟動該設備的引導。控制器掃描順序從檢測到的最低控制器邏輯單元號（LUN）到檢測到的最高LUN。附錄B中列出了控制器、設備及其LUN。REXROTH HMV01.1E-W0030-A-07-NNNN
Note If you are using a PROM version of the 162Bug (e.g., in noVMEbus, blank-flash versions of the MVME162FX controller) and you wish to execute the debugger out of Flash memory rather than from PROM in subsequent sessions, make sure that 162Bug is in Board Mode and copy the PROM contents to flash memory with the PFLASH command as follows:Then reinstall the jumper at J22 pins 9 and 10.REXROTH HMV01.1E-W0030-A-07-NNNN (162Bug always executes from memory location FF800000; the state of J22 determines whether that location is in PROM or flash.) Autoboot Autoboot is a software routine that is contained in the 162Bug Flash/PROM to provide an independent mechanism for booting an operating system. This autoboot routine automatically scans for controllers and devices in a specified sequence until a valid bootable device containing a boot media is found or the list is exhausted. If a valid bootable device is found, a boot from that device is started. The controller scanning sequence goes from the lowest controller Logical Unit Number (LUN) detected to the highest LUN detected. Controllers, devices, and their LUNs are listed in Appendix B.REXROTH HMV01.1E-W0030-A-07-NNNN
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.g2813.cn
