REXROTH MAC090C-0-GD-4-C/110-A-1伺服電機
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH MAC090C-0-GD-4-C/110-A-1伺服電機
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH MAC090C-0-GD-4-C/110-A-1檢查收割臺J21上的跳線安裝尺寸是否正確。連接J21上27C080設備的針腳1和2，或27C040設備的針腳2和3。出廠默認值為2和3。拆除J22引腳9和10上的跳線。注意：如果您希望在后續會話中使用閃存而不是PROM執行調試器，則需要在通電后初始化閃存，如步驟12所述。6.標頭J24上的跳線將IP總線時鐘配置為8MHz（在MVME162-4xx和-5xx板上）或32MHzREXROTH MAC090C-0-GD-4-C/110-A-1（僅限MVME162-5xx板）。工廠配置在J24引腳1和2之間安裝一條跳線，用于8MHz時鐘。驗證此設置是否適合您的應用程序。7.標頭J25上的跳線啟用/禁用MVME162FX上的IP總線選通功能。工廠配置在J25引腳1和2之間放置跳線，以將Strobe*信號連接到IP2芯片。驗證應用程序中是否連接了選通線。REXROTH MAC090C-0-GD-4-C/110-A-1
Check the jumper installation on header J21 for correct size. Connect pins 1 and 2 on J21 for 27C080 devices, or pins 2 and 3 for 27C040 devices. The factory default is 2 and 3.REXROTH MAC090C-0-GD-4-C/110-A-1Remove the jumper on J22 pins 9 and 10.Note If you wish to execute the debugger out of flash memory rather than from PROM in subsequent sessions, it will be necessary to initialize the flash memory after power-up as described in Step 12. 6. The jumper on header J24 configures the IP bus clock for either 8MHz (on both MVME162-4xx and -5xx boards) or 32MHz (on MVME162-5xx boards only). The factory configuration installs a jumper between J24 pins 1 and 2 for an 8MHz clock. Verify that this setting is appropriate for your application. 7. The jumper on header J25 enables/disables the IP bus strobe function on the MVME162FX. The factory configuration puts a jumper between J25 pins 1 and 2 to connect the Strobe? signal to the IP2 chip. Verify that the strobe line should be connected in your application.REXROTH MAC090C-0-GD-4-C/110-A-1
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.g2813.cn
