REXROTH MHD041B-144-PG0-UN伺服電機
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH MHD041B-144-PG0-UN伺服電機
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH MHD041B-144-PG0-UN如果隨后希望從閃存運行調試器，則必須首先使用PFLASH命令初始化閃存，然后重新配置J22。有關更多信息，請參閱下面的步驟5。安裝和啟動請按照下面的步驟使用REXROTH MHD041B-144-PG0-UN控制器操作162Bug。162Bug出廠時安裝在REXROTH MHD041B-144-PG0-UN的閃存中，沒有VMEbus的情況除外！小心在通電時插入或移除模塊可能會損壞模塊組件。1.關閉所有設備電源。請參閱第2章“硬件準備”一節，并根據特定應用的需要安裝/拆除集管上的跳線。收割臺J22上的跳線影響162Bug操作，如下所示。默認情況下，所有八個跳線都安裝在引腳1-2、3-4、5-6、7-8、9-10、11-12、13-14和15-16之間。沒有VMEbus接口的型號在引腳9-10之間沒有跳線。REXROTH MHD041B-144-PG0-UN
If you subsequently wish to run the debugger from Flash memory, you must first initialize Flash memory with the PFLASH command, then reconfigure J22. Refer to Step 5 below for additional information.Installation and Startup Follow the steps below to operate 162Bug with the MVME162FX controller. 162Bug is factory-installed in the flash memory of theREXROTH MHD041B-144-PG0-UN, except in the no-VMEbus case. ! Caution Inserting or removing modules while power is applied could damage module components. 1. Turn all equipment power OFF. Refer to the Hardware Preparation section in Chapter 2 and install/remove jumpers on headers as required for your particular application. Jumpers on header J22 affect 162Bug operation as listed below. The default condition is with all eight jumpers installed, between pins 1- 2, 3-4, 5-6, 7-8, 9-10, 11-12, 13-14, and 15-16. Models with no VMEbus interface have no jumper between pins 9-10.REXROTH MHD041B-144-PG0-UN
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.g2813.cn
