REXROTH MSK076C-0300-NN-M1-UG1-NNNN伺服電機
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH MSK076C-0300-NN-M1-UG1-NNNN伺服電機
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
請注意，有些電纜未隨REXROTH MSK076C-0300-NN-M1-UG1-NNNN系列模塊提供，必須由用戶自行制造或購買。摩托羅拉建議所有外圍連接使用屏蔽電纜，以盡量減少輻射。10.將外圍設備連接到電纜。附錄A提供了支持的EIA-232-D、EIA-530和EIA485/EIA-422信號的詳細信息。附錄B描述了SCSI（小型計算機系統接口）I/O總線連接。附錄C描述了以太網LAN（局域網）端口連接。11.在系統中安裝任何其他所需的VMEmodule。12.裝回機箱蓋。13.將電源電纜連接到交流電源，并打開設備電源。系統注意事項REXROTH MSK076C-0300-NN-M1-UG1-NNNN嵌入式控制器從VMEbus背板連接器P1和P2獲取電源。P2還用于32位傳輸中的高16位數據，以及擴展尋址模式中使用的高8位地址線。如果主板未連接到VMEbus背板連接器P1和P2，控制器可能無法正常工作。
Note that some cables are not provided with the REXROTH MSK076C-0300-NN-M1-UG1-NNNNseries module and must be made or purchased by the user. Motorola recommends shielded cable for all peripheral connections to minimize radiation. 10. Connect the peripheral(s) to the cable(s). Appendix A provides detailed information on the EIA-232-D, EIA-530, and EIA485/EIA-422 signals supported. Appendix B describes the SCSI (Small Computer System Interface) I/O bus connections. Appendix C describes the Ethernet LAN (Local Area Network) port connections. 11. Install any other required VMEmodules in the system. 12. Replace the chassis cover. 13. Connect the power cable to the AC power source and turn the equipment power ON.System Considerations The MVME162FX Embedded Controller draws power from VMEbus backplane connectors P1 and P2. P2 is also used for the upper 16 bits of data in 32-bit transfers, and for the upper 8 address lines used in extended addressing mode. The controller may not function properly without its main board connected to VMEbus backplane connectors P1 and P2.REXROTH MSK076C-0300-NN-M1-UG1-NNNN
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.g2813.cn
