FOXBORO FBM211 P0914TN輸入模塊
FOXBORO FBM211 P0914TN輸入模塊中文資料：
FOXBORO FBM211 P0914TN輸入模塊組裝一個基本的90-30系列PLC系統讓我們在紙上組裝一個使用以下組件的基本系統：基板電源模塊CPU模塊一些I/O模塊我們將從基板開始。為了保持簡單，我們將使用5個插槽大小。注意，5槽底板實際上有6個插槽，但電源插槽沒有編號。此外，請注意，該基板有一個CPU插槽，即插槽編號1，并且在右端有一個擴展連接器，如果系統有多個基板，則用于連接到另一個基板。接下來，我們將添加一個電源模塊。它安裝在基板左端的無編號插槽中。此插槽具有唯一的連接器，只能安裝電源模塊。然后添加CPU模塊。FOXBORO FBM211 P0914TNCPU模塊只能安裝在靠近電源的基板插槽1中。插槽1有一個唯一的連接器，只能安裝CPU或特殊選件模塊。CPU331圖1-3。CPU模塊最后，我們將向基板插槽2到5添加一些I/O模塊。要使這個基本系統正常工作，還需要什么？要使這個基本系統正常工作，您需要：安裝。將PLC安全、可靠地安裝在保護外殼中。接線。這包括正確安裝電源的輸入電源，以及從I/O模塊到現場設備（如開關、傳感器、螺線管、繼電器等）的接線。PLC運行的應用程序。這是用GE Fanuc PLC編程軟件開發的。FOXBORO FBM211 P0914TN
英文資料
Assembling a Basic Series 90-30 PLC System Let’s assemble, on paper, a basic system using the following components: ? Baseplate ? Power Supply module ? CPU module ? Some I/O modules We’ll start with the baseplate. To keep it simple, we’ll use a 5-slot size. Note that a 5-slot baseplate actually has six slots, but the power supply slot is not numbered. Note also, that this baseplate has a CPU slot, which is slot number 1, and it has an expansion connector on the right end, which is used for connecting to another baseplate if the system has more than one baseplate Next, we’ll add a power supply module. It mounts in the unnumbered slot on the left end of the baseplate. This slot has a unique connector that will only fit a power supply module.Then add a CPU module. A CPU module can only mount in baseplate slot 1, next to the power supply. Slot 1 has a unique connector that will only fit CPU or special Option modules. CPU331 Figure 1-3. CPU Module To finish, we will add some I/O modules to baseplate slots 2 through 5.What else would be needed to make this basic system functional? To make this basic system functional, you would need: ? Mounting. Safe, secure mounting for the PLC in a protective enclosure. ? Wiring. This includes properly installed incoming power to the power supply, as well as wiring from the I/O modules to field devices such as switches, sensors, solenoids, relays, etc. ? Program. An application program for the PLC to run. This is developed with GE Fanuc PLC programming software.FOXBORO FBM211 P0914TN
每 日 展 示
公 司 主 營 優 勢
應 用 行 業
