HIEE410372P201工業卡件,ABB卡件
HART:IC695ALG626 IC695ALK62865 IC695ALG728如果用于HART直通，支持RX3i PROFINET控制器（PNC001）和PROFINET掃描儀（PNS001或CEP001）還必須包含HART兼容固件：IC695PNC001固件版本2.20 IC695PNS001固件版本2.30或PNS10166 IC695CEP001固件版本2.3。PACSystems FDT HART DTM和PACSystems HART復用器的主要區別在于，它們設計用于不同類型的HART資產管理應用。·每當使用FDT框架應用程序（如GE Device Manager Essentials）配置和監控HART設備時，都會安裝PACSystems FDT HART DTM? 或其他FDT兼容的資產管理應用程序。·只要使用AMS配置和監測HART設備，就安裝PACSystems HART多路復用器? 來自艾默生過程管理?. 這兩種技術都需要主機PC和PLC之間的以太網通信。請注意，兩種解決方案中的PLC系統架構都相同。11.2帶HART的模擬輸入模塊16-/8通道電流/電壓：IC695ALG626 65如果使用，IC695ALD628必須安裝在RX3i CPU機架中。在發布時，PROFINET掃描儀IC695PNS001或IC695CEP001不支持它。有關未來更新，請參閱IC695PNS001或IC695CEP001的IPI。66與HART一起使用時，使用PNS101代替PNS001，通常不會用于事件序列應用。PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月帶有HART通信的模擬模塊496帶有HART的模擬輸入模塊8-/4通道電流/電壓：IC695ALG628 IC695ALD626 I1 I2 I3 I4 I5 16 I7 18 19 I10 I11 I12 I13 I14 I15 I16 Module OK FIELD STATUS TB圖312:IC695ALL626非隔離差分模擬電流/電壓輸入模塊IC695ALK628，提供8個單端或4個差分輸入通道。非隔離差分模擬電流/電壓輸入模塊IC695ALG626提供16個單端或8個差分輸入通道。兩個模塊在每個信道上都具有HART 5.0版通信功能。模塊IC695ALG626具有四個內部HART調制解調器。模塊IC695ALG628具有兩個內部HART調制解調器。在單端模式下，四個單端信道復用到每個HART調制解調器中。在差分模式下，兩個差分信道復用到每個HART調制解調器中。模擬輸入通道可配置為以下范圍：§電流：0至20mA、4至20mA、±20mA§電壓：±10 Vdc、0至10 Vdc、±5 Vdc、0到5 Vdc、1 Vdc到5 Vdc。將使用HART通信的信道必須配置為4-20mA范圍。11.2.1功能§完全軟件可配置，無需設置模塊跳線§完全自動校準§車載錯誤檢查§所有電壓和4-20mA輸入的開路檢測§每個通道的可配置縮放和偏移§高報警、低報警、高高報警、，每個通道可選擇的低-低報警檢測和報告§模塊故障報告§支持邏輯程序中的診斷點故障觸點§閃存用于未來升級§正負變化率報警§啟動時自動校準§通道報警和故障的可配置中斷§接線板插入或移除檢測§5.0版HART通信§這些模塊必須位于RX3i通用背板中。§模塊支持插入和取出通電的RX3i通用背板。參見第2.6.4.1節熱插拔。這些模塊可與盒型（IC694TBB032）、擴展盒型（IC 694TBB132）、彈簧型（IC6914TBS032）或擴展彈簧型（IC 6914TBS132）接線板一起使用。擴展接線板提供屏蔽布線所需的額外護罩深度。
HART: IC695ALG626 IC695ALG62865 IC695ALG728 If used for HART Pass Through, the supporting RX3i PROFINET Controller (PNC001) and PROFINET Scanner (PNS001 or CEP001) must also contain HART-compatible firmware: IC695PNC001 Firmware Release 2.20 IC695PNS001 Firmware Release 2.30 or PNS10166 IC695CEP001 Firmware Release 2.30. The primary difference between the PACSystems FDT HART DTMs and the PACSystems HART Multiplexer is that they are designed to work with different types of HART asset management applications. · The PACSystems FDT HART DTMs are installed whenever the HART devices will be configured and monitored using an FDT Frame Application such as GE Device Manager Essentials? or another FDTcompatible asset management application. · The PACSystems HART Multiplexer is installed whenever the HART devices will be configured and monitored using AMS? from Emerson Process Management?. Both technologies require Ethernet communications between the host PC and the PLC. Note that the architecture of the PLC system is the same in either solution. 11.2 Analog Input Module 16-/8-Channel Current/Voltage with HART: IC695ALG626 65 If used, IC695ALG628 must be installed in the RX3i CPU Rack. At time of publication, it is not supported by PROFINET scanners IC695PNS001 or IC695CEP001. Refer to IPIs for IC695PNS001 or IC695CEP001 for future updates. 66 When used with HART, the PNS101 is used in place of PNS001, and would not typically be employed for Sequence of Events application. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Modules with HART Communications 496 Analog Input Module 8-/4-Channel Current/Voltage with HART: IC695ALG628 IC695ALG626 I1 I2 I3 I4 I5 16 I7 18 19 I10 I11 I12 I13 I14 I15 I16 MODULE OK FIELD STATUS TB Figure 312: IC695ALG626 Non-Isolated Differential Analog Current/Voltage Input module, IC695ALG628, provides 8 single-ended or 4 differential input channels. Non-Isolated Differential Analog Current/Voltage Input module, IC695ALG626, provides 16 single-ended or 8 differential input channels. Both modules feature HART version 5.0 communications capability on each channel. Module IC695ALG626 has four internal HART modems. Module IC695ALG628 has two internal HART modems. In single-ended mode, four single-ended channels are multiplexed into each HART modem. In differential mode, two differential channels are multiplexed into each HART modem. Analog input channels can be configured for these ranges: § Current: 0 to 20mA, 4 to 20mA, ±20mA § Voltage: ±10 Vdc, 0 to 10 Vdc, ±5Vdc, 0 to 5Vdc, 1 Vdc to 5Vdc. Channels that will use HART communications must be configured for the 4- 20mA range. 11.2.1 Features § Completely software-configurable, no module jumpers to set § Full auto-calibration § On-board error-checking § Open-circuit detection for all voltage and 4-20mA inputs § Configurable scaling and offsets per channel § High alarm, low alarm, high-high alarm, low-low alarm detection and reporting selectable per channel § Module fault reporting § Supports diagnostic point fault contacts in the logic program § Flash memory for future upgrades § Positive and negative Rate of Change Alarms § Auto-calibration at startup § Configurable interrupts for channel alarms and faults § Terminal Block insertion or removal detection § Version 5.0 HART communications § These modules must be located in an RX3i Universal Backplane. § Modules support insertion into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1. The modules can be used with a Box-style (IC694TBB032), Extended Box-style (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132) Terminal Block. Extended terminal blocks provide the extra shroud depth needed for shielded wiring.
