HIEE451116RW01 FW9925a-E工控模塊機器人備件
請參閱上文。ON綠色：存在接線板。請參閱上文。OFF：模塊沒有背板電源。10.4.4規格：IC695ALG808輸出范圍電流：0至20mA，4至20mA電壓：±10 Vdc，0至10 Vdc ALG808-FA及更早版本背板電源要求：3.3V時最大450mA；對于ALG808-GB和更高版本，5.0V時最大25mA：3.3V時最大250mA；模塊內5.0V功耗時最大17mA最大7.25瓦（Vuser=24V）熱降級無需外部+電源電壓范圍：19.2V至30V（24V標稱）電流：660mA最大PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月模擬輸出模塊472分辨率±10 Vdc：15位，0至10 Vdc：14位，0到20mA:15位，4至20mA：15位輸出數據格式，可配置為浮點IEEE 32位或32位字段中的16位整數模擬更新速率（由I/O掃描時間確定，取決于應用程序）8 ms（近似值，所有8個通道）輸出過壓保護電流輸出僅：-30 V，持續60秒，+30V一小時校準精度64在25°C（從0到0.05mA，精度為±35μA）下精確到滿量程的0.10%以內在0-60°C（0到0.05毫安，精度為？0μA）時精確到滿刻度的0.25%以內輸出負載電抗電流：最大10μH，電壓：1μF最大最大輸出負載電流：1350W最大電壓：2kW最小輸出增益漂移電壓輸出：每攝氏度20ppm典型電流輸出：每華氏度35ppm典型輸出設定時間電壓或電流輸出：2ms，0至95%隔離，場至背板2550 Vdc，1秒隔離，每個通道10.4.5配置：IC695ALG008 10.4.5.1模塊參數默認描述輸出參考地址%AQxxxxx此模塊輸出數據的起始地址。這默認為下一個可用的%AQ塊。輸出參考長度16用于此模塊輸出數據的字數。無法更改此參數。輸出命令反饋參考地址%AIxxxxx
Refer to above. ON Green: Terminal block is present. Refer to above. OFF: No backplane power to module. 10.4.4 Specifications: IC695ALG808 Output Ranges Current: 0 to 20mA, 4 to 20mA Voltage: ±10 Vdc, 0 to 10 Vdc Backplane Power Requirements For ALG808-FA and earlier: 450mA maximum at 3.3V; 25mA maximum at 5.0V For ALG808-GB and later: 250mA maximum at 3.3V; 17mA maximum at 5.0V Power Dissipation within Module 7.25 Watts maximum (Vuser=24V) Thermal De-rating None required External +Power Supply Voltage Range: 19.2V to 30V (24V nominal) Current: 660mA maximum PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 472 Resolution ±10 Vdc: 15 bits, 0 to 10 Vdc: 14 bits, 0 to 20mA: 15 bits, 4 to 20mA: 15 bits Output Data Format Configurable as floating-point IEEE 32-bit or 16-bit integer in a 32-bit field Analog Update Rate (Determined by I/O scan time, application dependent) 8 ms (approximate, all eight channels) Output Over-voltage Protection Current outputs only: -30V for 60 seconds, +30V for one hour Calibrated Accuracy64 Accurate to within 0.10% of full scale at 25°C (From 0 to 0.05mA, accuracy is ±35μA) Accurate to within 0.25% of full scale at 0-60°C (From 0 to 0.05mA, accuracy is ±70μA) Output Load Reactance Current: 10μH maximum, Voltage: 1μF maximum Maximum Output Load Current: 1350W maximum Voltage: 2kW minimum Output Gain Drift Voltage output: 20ppm per degree C typical Current output: 35ppm per degree C typical Output Settling Time Voltage or current output: 2ms, 0 to 95% Isolation, Field to Backplane 2550 Vdc for one second Isolation, Channel to Channel 250 Vac continuous 1500 Vac for one minute per channel 10.4.5 Configuration: IC695ALG808 10.4.5.1 Module Parameters Parameter Default Description Outputs Reference Address %AQxxxxx Starting address for the output data of this module. This defaults to the next available %AQ block. Outputs Reference Length 16 The number of words used for the output data of this module. This parameter cannot be changed. Output Command Feedback Reference Address %AIxxxxx Stating address for the
