HIMA F2102處理器卡件
是符號位。范圍分辨率范圍限制0至20 mA 15位0至32767 4至20 mA 16位0至3296763 0至10 Vdc 15位0到32767-10 Vdc至10 Vdc 16位-32768至32767 10.3.5.1狀態數據：ALG392此模塊使用8或16個離散輸入位，如配置所示。低8位用于模塊狀態信息，如下圖所示。在當前模式下，各個通道也可以報告斷線診斷。這些診斷以高8位報告，如圖所示：63 in 4-20可配置為作為電壓輸出或電流輸出運行，而不是同時運行。10.3.7配置：ALG392參數描述值默認值激活信道掃描的信道數1到8 1模塊輸出數據參考地址輸出范圍0、+10 Vdc±10 Vdc 4、20 mA 0、20 mA 1、10 Vdc激活信道表示PLC CPU將掃描的信道數量。對STOP模式所做的選擇決定了當從RUN（運行）模式轉到STOP（停止）模式時，該模塊上的輸出是否保持其最后狀態或默認為零。%AQ參考地址參數選擇%AQ內存中將開始向模塊輸出數據的區域的起始位置。%I參考地址選擇%I內存中該模塊狀態數據區域的起始位置。如果長度設置為8，則只報告模塊狀態。如果長度設置為16，則還將報告作為電流輸出運行的信道的信道狀態。每個通道可設置為在四個輸出范圍之一上運行：? 0至10 Vdc（默認值）? -10 Vdc至+10 Vdc范圍? 4至20 mA和0至20 mA? 0至20 mA 10.3.8模擬輸出模塊4通道電流/電壓：IC695ALG004模擬輸出模塊8通道電流/電流：IC695AlG008 PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月模擬輸出模塊449模塊OK FIELD STATUS TB IC695ALG708 Q1 Q2 Q4 Q5 Q6 Q7 Q8圖304:IC695ALL708模擬電流/電壓輸出模塊IC695ALD704，提供四個非隔離的可配置電壓或電流輸出通道。模擬電流/電壓輸出模塊IC695ALG008（圖304）提供八個非隔離的可配置電壓或電流輸出通道。可以為以下輸出范圍配置模擬通道：? 電流：0至20mA，4至20mA? 電壓：±10 Vdc，0至10 Vdc這些模塊可與盒型（IC694TBB032）、擴展盒型（IC 694TBB132）、彈簧型（IC6914TBS032）或擴展彈簧型（IC 6914TBS132）接線板一起使用。擴展接線板提供屏蔽布線所需的額外護罩深度。有關接線板的更多信息，請參閱第17章。接線板單獨訂購。這些模塊必須位于RX3i通用背板中。它們需要固件版本為3.0或更高版本的RX3i CPU。必須使用Machine Edition 5.0 SP3 Logic Developer PLC或更高版本進行配置。10.3.9隔離+24V直流電源模塊必須從外部電源接收其24Vdc電源。外部電源必須直接連接到此模塊的接線板。它不能通過RX3i通用背板上的TB1連接器連接。10.3.10特點：ALG704和ALG708? 完全軟件可配置，無需設置模塊跳線? 單獨啟用或禁用通道? 夾緊和報警限值? 警報的鎖定? 可配置輸出偏置? 基于濾波器頻率的快速信道捕獲時間? 全自動校準? 車載錯誤檢查? 每個通道可配置的縮放和偏移? 每個通道可選擇高報警、低報警、高高報警、低低報警檢測和報告? 模塊故障報告? 可配置的保持上次狀態或輸出默認值? 模塊支持插入和取出通電的RX3i通用背板。參見第2.6.4.1節熱插拔。? 模塊支持使用WinLoader軟件實用程序（如果主機CPU具有串行端口）或使用基于Web的工具（如果主機沒有串行端口）進行固件升級。固件升級套件中包含說明。2
.is the sign bit. Range Resolution Range Limits 0 to 20 mA 15 bits 0 to 32767 4 to 20 mA 15 bits 0 to 3276763 0 to 10 Vdc 15 bits 0 to 32767 -10 Vdc to 10 Vdc 16 bits - 32768 to 32767 10.3.5.1 Status Data: ALG392 This module uses either 8 or 16 discrete input bits, as configured. The lower 8 bits are used for module status information as displayed in the following figure. In current mode, individual channels can also report Broken Wire diagnostics. Those diagnostics are reported in the upper eight bits, as shown: 63 In 4-20 can be configured to operate as a voltage output or a current output - not both simultaneously. 10.3.7 Configuration: ALG392 Parameter Description Values Default Values Active Channels Number of channels scanned 1 through 8 1 Reference Address for Module Output Data Starting Type of Output Range 0, +10 Vdc ±10 Vdc 4, 20 mA 0, 20 mA 0, 10 Vdc Active Channels indicates the number of channels that will be scanned by the PLC CPU. The choice made for STOP Mode determines whether the outputs on this module will hold their last states or default to zero when the goes from RUN to STOP mode. The %AQ Reference Address parameter selects the start of the area in the %AQ memory where the output data to the module will begin. The %I Reference Address selects the start of the area in %I memory for the status data of this module. If the length is set to 8, then only module status will be reported. If the length is set to 16, channel status will also be reported for channels that are operating as current outputs. Each channel can be set up to operate on one of four output ranges: ? 0 to 10 Vdc (default) ? -10 Vdc to +10 Vdc range ? 4 to 20 mA, and 0 to 20 mA ? 0 to 20 mA 10.3.8 Analog Output Module 4-Channel Current/Voltage: IC695ALG704 Analog Output Module 8-Channel Current/Voltage: IC695ALG708 PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 449 MODULE OK FIELD STATUS TB IC695ALG708 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Figure 304: IC695ALG708 The Analog Current/Voltage Output module, IC695ALG704, provides four non-isolated configurable voltage or current output channels. The Analog Current/Voltage Output module, IC695ALG708 (Figure 304), provides eight non-isolated configurable voltage or current output channels. Analog channels can be configured for these output ranges: ? Current: 0 to 20mA, 4 to 20mA ? Voltage: ± 10 Vdc, 0 to 10 Vdc These modules can be used with a Box-style (IC694TBB032), Extended Boxstyle (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132) Terminal Block. Extended terminal blocks provide the extra shroud depth needed for shielded wiring. Refer to Chapter 17 for more information about Terminal Blocks. Terminal Blocks are ordered separately. These modules must be located in an RX3i Universal Backplane. They require an RX3i CPU with firmware version 3.0 or later. Machine Edition Version 5.0 SP3 Logic Developer-PLC or later must be used for configuration. 10.3.9 Isolated +24Vdc Power The module must receive its 24Vdc power from an external source. The external source must be connected directly to the terminal block of this module. It cannot be connected via the TB1 connector on the RX3i Universal Backplane. 10.3.10 Features: ALG704 & ALG708 ? Completely software-configurable, no module jumpers to set ? Individually enable or disable channels ? Clamping and Alarm Limits ? Latching of Alarms ? Configurable output bias ? Rapid channel acquisition times based on filter frequency ? Full auto-calibration ? On-board error-checking ? Configurable scaling and offsets per channel ? High alarm, low alarm, high-high alarm, low-low alarm detection and reporting selectable per channel ? Module fault reporting ? Configurable Hold Last State or Output Defaults ? Module supports insertion into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1. ? Module supports firmware upgrades using the WinLoader software utility (if the host CPU has a serial port) or using a Web-based tool (if the host CPU has no serial port). Instructions are included with the firmware upgrade kit.2
