HIMA F3113卡件
l限制。高報警（Eng單位）低報警（Eng單位）低-低報警（Eng單位）高-高報警死區（Eng單元）高報警死區。該值在報警檢查之前添加到通道上的縮放值。禁用/啟用軟件過濾。控制是否對輸入執行軟件過濾。積分時間（毫秒）0指定軟件篩選器達到輸入值63.2%的時間量（毫秒）。值為0表示軟件過濾器已禁用。值為100表示數據將在100毫秒內達到其值的63.2%。默認值為0。PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊419 9.11.1.2使用報警：ALG608和ALG616診斷報告啟用、故障報告啟用和中斷啟用配置參數可用于為單個通道報警啟用不同類型的響應。默認情況下，在每個通道上禁用所有響應。可以為每個通道配置報警啟用的任何組合。? 如果啟用了診斷報告，模塊將在該通道的診斷參考地址的參考存儲器中報告通道報警。? 如果啟用了故障報告，則模塊會在I/O故障表中記錄每次通道報警的故障日志。? 如果啟用了中斷，警報可以觸發應用程序中中斷塊的執行，如下所述。9.11.1.3使用中斷：ALG608和ALG616要正確配置I/O中斷，必須在模塊的配置文件中設置中斷啟用位。此外，應響應信道中斷而執行的程序塊必須映射到相應信道的參考地址。示例：在此示例中，通道值參考地址塊映射到%AI0001-%AI0020。如果通道2出現高報警條件，應觸發I/O中斷塊。? 配置高報警條件。? 在模塊配置中設置通道2的高報警中斷啟用標志。通道2的參考地址對應于%AI00003（每個通道2個字），因此應為“I/O中斷”類型設置中斷程序塊調度屬性，并將“%AI0003”設置為觸發器。9.11.1.3.1故障報告和中斷：ALG608和ALG616這些模塊具有診斷報告和中斷的單獨啟用/禁用選項。通常，禁用配置中的診斷（如低/高報警或過高/過低范圍）意味著其診斷位從未設置。但是，如果為某個條件啟用了中斷并且發生了該中斷，則在I/O中斷塊邏輯執行期間也會設置該條件的診斷位。下一次PLC輸入掃描總是將此中斷狀態位清除回0，因為診斷報告已禁用。9.11.2模塊數據：ALG608和ALG616模塊以其配置的輸入字報告其輸入信道數據，從其分配的信道值參考地址開始。每個信道占用兩個字（無論是否使用信道）：信道值參考地址包含此輸入+0，1信道1 PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊420+2，3信道2+4，5信道3+6，7信道4+8，9信道5+10，11信道6+12，13信道7+14，15信道8僅用于模塊IC695ALG616：+16，17信道9+18，19信道10+20、21信道11+22、23信道12+24、25信道13+26、27信道14+28、29信道15+30、31信道16根據其配置的信道值格式，每個啟用的信道向CPU報告32位浮點或16位整數值。在16位整數模式中，32位通道數據區的低位字包含16位整數通道值。32位的高位字（高位16位）
imits. High Alarm (Eng Units) Low Alarm (Eng Units) Low-Low Alarm (Eng Units) High-High Alarm Deadband (Eng Units) High Alarm Deadband (Eng Units) Low Alarm Deadband (Eng Units) Low-Low Alarm Deadband (Eng Units) User Offset 0.0 Engineering Units offset to change the base of the input channel. This value is added to the scaled value on the channel prior to alarm checking. Software Filtering Disabled Disabled / Enabled. Controls whether software filtering will be performed on the inputs. Integration Time (ms) 0 Specifies the amount of time in milliseconds for the software filter to reach 63.2% of the input value. A value of 0 indicates software filter is disabled. A value of 100 indicates data will achieve 63.2% of its value in 100ms. Default is 0. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 419 9.11.1.2 Using Alarming: ALG608 & ALG616 The Diagnostic Reporting Enable, Fault Reporting Enable, and Interrupt Enable configuration parameters can be used to enable different types of responses for individual channel alarms. By default, all responses are disabled on every channel. Any combination of alarm enables can be configured for each channel. ? If Diagnostic Reporting is enabled, the module reports channel alarms in reference memory at the Diagnostic Reference address for that channel. ? If Fault Reporting is enabled, the module logs a fault log in the I/O Fault table for each occurrence of a channel alarm. ? If Interrupts are enabled, an alarm can trigger execution of an Interrupt Block in the application program, as explained below. 9.11.1.3 Using Interrupts: ALG608 & ALG616 To properly configure an I/O Interrupt, the Interrupt enable bit or bits must be set in the configuration profile of the module. In addition, the program block that should be executed in response to the channel interrupt must be mapped to the reference address of the corresponding channel. Example: In this example, the Channel Values Reference Address block is mapped to %AI0001-%AI0020. An I/O Interrupt block should be triggered if a High Alarm condition occurs on channel 2. ? Configure the High-Alarm condition. ? Set the High-Alarm Interrupt Enable flag for Channel 2 in the module configuration. The reference address for Channel 2 corresponds to %AI00003 (2 Words per channel), so the interrupt program block Scheduling properties should be set for the "I/O Interrupt" Type and "%AI0003" as the Trigger. 9.11.1.3.1 Fault Reporting and Interrupts: ALG608 & ALG616 These modules have separate enable/disable options for Diagnostic Reporting and Interrupts. Normally, disabling a diagnostic (such as Low/High Alarm or Over/Under range) in the configuration means that its diagnostic bit is never set. However, if interrupts are enabled for a condition and that interrupt occurs, the diagnostic bit for that condition is also set during the I/O Interrupt block logic execution. The next PLC input scan always clears this interrupt status bit back to 0, because Diagnostic Reporting has it disabled. 9.11.2 Module Data: ALG608 & ALG616 The module reports its input channel data in its configured input words, beginning at its assigned Channel Value Reference Address. Each channel occupies two words (whether the channel is used or not): Channel Value Reference Address Contains this Input +0, 1 Channel 1 PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 420 +2, 3 Channel 2 +4, 5 Channel 3 +6, 7 Channel 4 +8, 9 Channel 5 +10, 11 Channel 6 +12, 13 Channel 7 +14, 15 Channel 8 For Module IC695ALG616 Only: +16, 17 Channel 9 +18, 19 Channel 10 +20, 21 Channel 11 +22, 23 Channel 12 +24, 25 Channel 13 +26, 27 Channel 14 +28, 29 Channel 15 +30, 31 Channel 16 Depending on its configured Channel Value Format, each enabled channel reports a 32-bit floating-point or 16-bit integer value to the CPU. In the 16-bit integer mode, the low word of the 32-bit channel data area contains the 16-bit integer channel value. The high word (upper 16-bits) of the 32-bit
