HIMA F3209工控自動化卡件
標準和一般規范，請參考附錄A59。在存在嚴重RF干擾（IC 801-3，10V/m）的情況下，精度可能會降低±1.5%的范圍。PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊413 9.10.4配置：ALG608和ALG616 9.10.4.1模塊參數：ALG628和ALG66參數默認描述信道值參考地址%AIxxxxx模塊輸入數據的起始地址。這默認為下一個可用的%AI塊。信道值參考長度ALG608：16用于模塊輸入數據的字數。無法更改此參數。ALG616:32診斷參考地址%Ixxxxx通道診斷狀態數據的起始地址。診斷參考長度0信道診斷數據所需的位參考位數。設置為0時，通道診斷被禁用。要啟用通道診斷映射，請將其更改為非零值。模塊狀態參考地址%Ixxxxx模塊狀態數據的起始地址。模塊狀態參考長度0模塊狀態數據所需的位數（0到32）。設置為0時，模塊狀態數據的映射被禁用。要啟用模塊狀態數據映射，請將其更改為非零值。I/O掃描集1將模塊I/O狀態數據分配給CPU配置中定義的掃描集。確定RX3i輪詢數據輸入默認強制關閉的頻率。如果模塊發生故障或移除，此參數指定模塊所有通道值參考的狀態。強制關閉=通道值清除為0。保持最后狀態=頻道保持其最后狀態。未啟用/禁用端子塊的輸入默認值：控制如果端子塊被移除，輸入是否將設置為默認值。PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊414參數默認描述信道故障，無端子板禁用啟用/禁用：控制端子板移除后是否生成信道故障和配置的報警響應。如果禁用，則移除接線板時，通道故障和警報將被抑制。此設置不會影響模塊故障，包括接線板丟失/添加故障生成。模擬輸入模式單端輸入模式單端口/差分：此選擇必須是16位整數或32位浮點高標度值（英制單位）四個標度參數的默認值取決于配置的量程類型和量程。每個范圍和范圍類型都有一組不同的默認值。注：如果高量程工程單位等于高量程A/D單位，而低量程工程單位則等于低量程A/D單位時，則禁用縮放。默認值為所選范圍類型的A/D上限。低量程值（工程單位）默認值為所選量程類型的低A/D限值。必須低于高縮放值。高比例值（A/D單位）默認值為所選范圍類型的高A/D限制。必須大于低縮放值。低比例值
standards and general specifications, refer to Appendix A. 59 In the presence of severe RF interference (IC 801-3, 10V/m), accuracy may be degraded by ±1.5% of range. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 413 9.10.4 Configuration: ALG608 & ALG616 9.10.4.1 Module Parameters: ALG608 & ALG616 Parameter Default Description Channel Value Reference Address %AIxxxxx Starting address for the input data of the module. This defaults to the next available %AI block. Channel Value Reference Length ALG608: 16 The number of words used for the input data of the module. This parameter cannot be changed. ALG616: 32 Diagnostic Reference Address %Ixxxxx Starting address for the channel diagnostics status data. Diagnostic Reference Length 0 The number of bit reference bits required for the Channel Diagnostics data. When set to 0, Channel Diagnostics is disabled. To enable Channel Diagnostics mapping, change this to a non-zero value. Module Status Reference Address %Ixxxxx Starting address for the status data of the module. Module Status Reference Length 0 The number of bits (0 to 32) required for the Module Status data. When set to 0, mapping of Module Status data is disabled. To enable Module Status data mapping, change this to a non-zero value. I/O Scan Set 1 Assigns the module I/O status data to a scan set defined in the CPU configuration. Determines how often the RX3i polls the data Inputs Default Force Off In the event of module failure or removal, this parameter specifies the state of all Channel Value References for the module. Force Off = Channel Values clear to 0. Hold Last State = Channels hold their last state. Inputs Default w/o Terminal Block Enabled Enabled / Disabled: Controls whether inputs will be set to their defaults if the Terminal Block is removed. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 414 Parameter Default Description Channel Faults w/o Terminal Block Disabled Enabled / Disabled: Controls whether channel faults and configured alarm responses are generated after Terminal Block removal. If Disabled, channel faults and alarms are suppressed when the Terminal Block is removed. This setting does not affect module faults including the Terminal Block loss/add fault generation. Analog Input Mode Single-ended Input Mode Single-ended / Differential: This selection must 16-bit integer or 32-bit floating-point High Scale Value (Eng Units) The defaults for the four Scaling parameters depend on the configured Range Type and Range. Each Range and Range Type has a different set of defaults. Note: Scaling is disabled if both High Scale Eng. Units equals High Scale A/D Units and Low Scale Eng. Units equals Low Scale A/D Units. Default is High A/D Limit of selected range type. Low Scale Value (Eng Units) Default is Low A/D Limit of selected range type. Must be lower than the high scaling value. High Scale Value (A/D Units) Default is High A/D Limit of selected range type. Must be greater than the low scaling value. Low Scale Value
