HIMA F32100 H51A-HRS機械設備卡件
該模塊可與盒型（IC694TBB032）、擴展盒型（IC 694TBB132）、彈簧型（IC6914TBS032）或擴展彈簧型（IC 6914TBS132）接線板一起使用。擴展接線板提供屏蔽布線所需的額外護罩深度。有關接線板的更多信息，請參閱第17章。接線板單獨訂購。這些模塊必須位于RX3i通用背板中。9.10.1特點? 完全軟件可配置，無需設置模塊跳線? 全自動校準? 車載錯誤檢查? 所有電壓和4-20mA輸入的開路檢測? 每個通道可配置的縮放和偏移? 每個通道可選擇高報警、低報警、高高報警、低低報警檢測和報告? 模塊故障報告? 支持邏輯程序中的診斷點故障觸點? 用于未來升級的閃存? 正負變化率報警? 啟動時自動校準? 通道報警和故障的可配置中斷? 接線板插入或移除檢測? 模塊支持插入和取出通電的RX3i通用背板。參見第2.6.4.1節熱插拔。PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊410 9.10.2 LED：ALG608和ALG616模塊OK LED指示模塊狀態。現場狀態LED指示至少一個通道上存在故障或接線板錯誤。TB（端子塊）LED指示是否存在端子塊。LED由背板電源總線供電。LED指示模塊正常開啟綠色：模塊正常且已配置。綠色或琥珀色緩慢閃爍：模塊正常，但未配置。快速閃爍綠色：錯誤。OFF：模塊故障或無背板電源現場狀態ON綠色：任何已啟用通道上無故障，且存在接線板。ON黃色：至少一個通道出現故障。OFF：接線板不存在或未完全就位。TB ON紅色：接線板不存在或未完全就位。ON綠色：存在接線板。OFF：模塊沒有背板電源。9.10.3及更早版本的最大4.83W-FB及更高版本的最大2.58W ALG616-EA及更早版本最大6.48W-FB和更高版本最大4.25W熱降級無分辨率參考本節中的分辨率和量程類型表。輸入數據格式可配置為32位字段中的浮點IEEE 32位或16位整數濾波器選項8Hz、12Hz、16Hz、40Hz、200Hz、500Hz模塊掃描時間（以毫秒為單位）模塊掃描最多可包含四個采集周期。每個周期包括一組特定的通道，如“通道掃描”一節所述。總掃描時間取決于掃描中的采集周期數和配置的過濾器選項。配置的濾波器編號412正常模式噪聲抑制（單位：dB）50Hz 60Hz 8 Hz濾波器103 97定期校準調整。隔離電壓接線板至背板/底盤光電隔離，變壓器隔離250 Vac連續/1500 Vac 1分鐘用于產品
This module can be used with a Box-style (IC694TBB032), Extended Boxstyle (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132) terminal Block. Extended terminal blocks provide the extra shroud depth needed for shielded wiring. Refer to Chapter 17 for more information about Terminal Blocks. Terminal Blocks are ordered separately. These modules must be located in an RX3i Universal Backplane. 9.10.1 Features ? Completely software-configurable, no module jumpers to set ? Full auto-calibration ? On-board error-checking ? Open-circuit detection for all voltage and 4-20mA inputs ? Configurable scaling and offsets per channel ? High alarm, low alarm, high-high alarm, low-low alarm detection and reporting selectable per channel ? Module fault reporting ? Supports diagnostic point fault contacts in the logic program ? Flash memory for future upgrades ? Positive and negative Rate of Change Alarms ? Auto-calibration at startup ? Configurable interrupts for channel alarms and faults ? Terminal Block insertion or removal detection ? Module supports insertion into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1. PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 410 9.10.2 LEDs: ALG608 & ALG616 The Module OK LED indicates module status. The Field Status LED indicates the presence of a fault on at least one channel or a terminal block error. The TB (Terminal Block) LED indicates the presence or absence of the terminal block. LEDs are powered by the backplane power bus. LED Indicates Module OK ON Green: Module OK and configured. Slow Flashing Green or Amber: Module OK but not configured. Quick Flashing Green: Error. OFF: Module is defective or no backplane power present Field Status ON Green: No faults on any enabled channel, and Terminal Block is present. ON Yellow: Fault on at least one channel. OFF: Terminal block not present or not fully seated. TB ON Red: Terminal block not present or not fully seated. ON Green: Terminal block is present. OFF: No backplane power to module. 9.10.3 & earlier 4.83W max -FB & later 2.58W max ALG616 -EA & earlier 6.48W max -FB & later 4.25W max Thermal De-rating None Resolution Refer to the table Resolution and Range Types in this section. Input Data Format Configurable as floating-point IEEE 32-bit or 16-bit integer in a 32-bit field Filter Options 8Hz, 12Hz, 16Hz, 40Hz, 200Hz, 500Hz Module Scan Time (in ms) The module scan can consist of up to four acquisition cycles. Each cycle includes a specific set of channels, as described in the section “Channel Scanning”. Total Scan Time depends on the number of acquisition cycles in the scan, and the configured filter option. Configured Filter Number 412 Normal Mode Noise Rejection in dB At 50Hz At 60Hz 8 Hz filter 103 97 periodic calibration adjustment. Isolation Voltage terminal block to backplane/chassis Opto-isolated, transformer isolated 250 Vac continuous/1500 Vac for 1 minute For product
