HIMA F4102電源模塊,模塊控制器
RX3i系統手冊第3節GFK-2314T 2019年9月安裝45 2.6.4.3安裝模塊警告模塊的螺絲端子上可能存在潛在的危險電壓，即使背板的電源已關閉。在處理模塊的可拆卸端子板及其連接的任何電線時，始終要小心。? 確保模塊目錄號與預期的插槽配置相匹配。? 牢牢握住模塊，將模塊與正確的插槽和連接器對齊。? 將模塊的后樞軸鉤（圖24）接合在背板（1）頂部的槽口中。? 向下擺動模塊（2），直到模塊的連接器與背板連接器接合，模塊底部的釋放桿卡入底部模塊固定器（3）中。? 目視檢查模塊，確保其正確就位。1 2 3圖24：在背板中安裝模塊2.6.4.4卸下模塊PACSystems*RX3i系統手冊第3節GFK-2314T 2019年9月安裝46? 如果模塊具有可拆卸的端子板，請按照本節后面的說明將其拆下。? 將釋放桿定位在模塊底部（圖25），并朝模塊方向用力向上按壓（1）。較寬的模塊有兩個釋放桿，必須同時向上按壓。? 牢牢握住模塊并完全按下釋放桿時，向上轉動模塊，直到其連接器脫離背板（2）。? 向上提起模塊并使其遠離背板，以松開樞軸鉤。1 2 3圖25：從背板上卸下模塊2.6.4.5 I/O模塊接線板組件PACSystems*RX3i系統手冊第3節GFK-2314T 2019年9月安裝47大多數PACSystems RX3i I/O模塊具有可拆卸的前接線板組件。這種類型的每個模塊都有一個門標簽，可以移除，根據應用需要標記，然后重新插入固定槽中（圖28）。標簽的正面（圖26）顯示模塊的目錄號和指示模塊類型的色帶。它還提供空間來記錄關于連接到模塊的輸入或輸出的識別應用信息。接線圖印在反面，一旦門打開，技術人員就可以看到（圖27）。接線板具有完全鉸接的門，可以向左或向右打開，以接近接線。REL EASE LEV ER Q1 Q2 Q3 Q4 Q5 Q6 IC694MDL734圖26模塊門標簽前視圖圖27：門背面接線圖圖28：應用程序標記后插入門標簽2.6.4.6 I/O模塊連接PACSystems*RX3i系統手冊第3節GFK-2314T 2019年9月安裝48對于大多數RX3i I/O模塊，連接到模塊的可拆卸端子板。每個模塊的具體接線信息打印在門插件上，也顯示在本手冊中的模塊說明中。本節介紹了大多數RX3i I/O模塊使用的20連接器可拆卸接線板（圖29）。高密度模塊使用其他連接方法。有關以下內容的詳細信息，請參閱第17章：? 用于大多數高密度模塊的36針可拆卸接線板。? 與模塊前部有兩個20-連接器連接器的I/O模塊的連接。? 端子板快速連接（TBQC）系統，允許用戶將現場接線連接到插入式端子板上，并使用預制互連電纜完成與I/O模塊的連接。20連接器接線板上的螺紋端子可接受兩條AWG#22（0.36 mm2）至兩條AWG#16（1.3 mm2）或一條AWG#14（2.1 mm2）90°C（194°F）銅線。每個端子都可以接受實心線或絞合線，但進入任何給定端子的導線應為相同類型（實心線或雙絞合線），以確保良好連接。電線從端子板空腔底部布線到端子。I/O端子板連接螺釘的建議扭矩為1.1至1.3 Nm（9.6至11.5 in-lb）。接線完成后，電線應捆扎并固定在接線板底部，如圖29所示。
RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 45 2.6.4.3 Installing Modules WARNING Potentially dangerous voltages may be present on the screw terminals of the module, even though power to the backplane is turned off. Always be careful when handling the removable terminal board of the module and any wires connected to it. ? Be sure the module catalog number matches the intended slot configuration. ? Holding the module firmly, align the module with the correct slot and connector. ? Engage the rear pivot hook(s) of the module (Figure 24) in the notch(es) on the top of the backplane (1). ? Swing the module down (2) until the connector of the module engages the backplane connector, and the release lever(s) on the bottom of the module snaps into place in the bottom module retainer (3). ? Visually inspect the module to be sure it is properly seated. 1 2 3 Figure 24: Installing Module in Backplane 2.6.4.4 Removing Modules PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 46 ? If the module has a removable terminal board, remove it as described later in this section. ? Locate the release lever(s) at the bottom of the module (Figure 25) and firmly press upward (1), toward the module. Wider modules have two release levers that must both be pressed up at the same time. ? While holding the module firmly and fully depressing the release lever(s), pivot the module upward until its connector is out of the backplane (2). ? Lift the module up and away from the backplane to disengage the pivot hook. 1 2 3 Figure 25: Removing Module from Backplane 2.6.4.5 I/O Module Terminal Block Assemblies PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 47 Most PACSystems RX3i I/O modules have removable front terminal block assemblies. Each module of this type has a door label that can be removed, marked up as required for the application, then re-inserted into the retaining grooves, (Figure 28). The front of the label (Figure 26) displays the catalog number of the module and a color band to indicate the module type. It also provides space to record identifying application information about the inputs or outputs wired to the module. The wiring diagram is printed on the reverse side and is visible to the technician (Figure 27) once the door is swung open. The terminal blocks have fully-hinged doors that can be opened to either the left or right to access wiring. REL EASE LEV ER Q1 Q2 Q3 Q4 Q5 Q6 IC694MDL734 Figure 26 Module Door Label Front View Figure 27: Wiring Diagram on Reverse Side of Door Figure 28: Insertion of Door Label following Mark-up for Application 2.6.4.6 I/O Module Connections PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 48 For most RX3i I/O modules, connections are made to the removable terminal board of the module. Specific wiring information for each module is printed on the door insert and also shown in the module description in this manual. This section describes the 20-Connector removable terminal block (Figure 29), which is used by most RX3i I/O modules. Higher-density modules use other connection methods. Refer to Chapter 17 for details concerning the following: ? 36-pin removable terminal blocks used for most higher-density modules. ? Connections to I/O modules that have two 20- Connector connectors on the front of the module. ? Terminal Board Quick Connect (TBQC) system that allows users to land the field wiring on interposing terminal strips and complete the connection to the I/O module using pre-fabricated interconnect cables. Screw terminals on a 20-Connector terminal block accept from two AWG #22 (0.36 mm2 ) to two AWG #16 (1.3 mm2 ), or one AWG #14 (2.1 mm2 ) copper 90°C (194°F) wire(s). Each terminal can accept solid or stranded wires, but the wires into any given terminal should be the same type (both solid or both stranded) to ensure a good connection. Wires are routed to and from the terminals out of the bottom of the terminal board cavity. The suggested torque for the I/O terminal board connection screws is from 1.1 to1.3 Nm (9.6 to 11.5 in-lb). After the wiring is completed, wires should be bundled and fastened at the bottom of the terminal block, as shown in Figure 29.
