HONEYWELL 51306521-175 CC-TAON11模塊控制器
啟動將被阻止，直到有足夠的熱容量。5.4.2平均電機負載路徑：實際值×A3學習數據×平均電機負載469可以學習一段時間內的平均電機負載。該時間由S1 469 SETUP（設置）×PREFERENCES（首選）×AVERAGE MOTOR LOAD CALC.PERIOD（平均電機負載計算周期）設定值指定（默認為15分鐘）。該計算是一個滑動窗口，在電機啟動期間被忽略。n電機啟動n[輸入]了解更多學習加速時間：0.0 s范圍：0.0至200.0秒。學習啟動電流：0 A范圍：0至50000 A學習啟動容量：0%使用范圍：0到100%上次加速時間：0.0s范圍：0.0~200.0秒。最后啟動電流：0 A范圍：0至50000 A最后啟動容量：0%使用范圍：0到100%平均電機負載n[ENTER]了解更多平均電機負載學習值：0.00 x FLA范圍：0.00到20.00 ENTER ESCAPE（輸入退出）RTD最大值路徑：實際值×A3學習數據×RTD最大值469將學習每個RTD的最大溫度?？墒褂肧1 469 SETUP（設置）×CLEAR DATA（清除數據）×CLER RTD MAXIMUMS（清除RTD最大值）設定點清除此信息。如果在S8 RTD TEMPERATURE（S8 RTD溫度）中未編程RTD，則嘗試輸入這組信息時將顯示以下閃爍信息。n RTD MAXIMUMS n[ENTER]更多RTD#1最大溫度：40°C范圍：-50至250°C，無RTD（開路），----（短路）。僅當模擬輸入自上次清除以來至少有1個最大值時才可見。該信息可通過S1 469 SETUP？CLEAR DATA？CLEAR ANALOG I/P MIN/MAX設置點清除。清除數據后，每個模擬輸入的當前值將作為最小值和最大值的起點加載。輸入名稱和單位將反映為每個輸入編程的名稱。如果在S12模擬輸入/輸出中未編程模擬輸入，當試圖輸入這組信息時，將出現以下閃爍信息。n ANALOG IN MIN/MAX n[ENTER]（模擬輸入最小值/最大值），了解更多模擬I/P 1最小值：O單位范圍：–50000至50000。如果模擬輸入設置為無，則不可見。將模擬輸入名稱反映為編程的模擬I/P 1 MAX:0單位范圍：-50至250°C，無RTD（開路），----（短路）。如果RTD設置為無，則不可見；將RTD名稱反映為編程的模擬I/P 2 MIN:O單位范圍：-50至250°C，無RTD（開路），----（短路）。如果RTD設置為無，則不可見；將RTD名稱反映為編程的模擬I/P 2最大值：0??MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MISSAGE ESCAP MESSAGE ESCAPE MESAGE ESCAPE GE Multilin 469電機管理繼電器5-19 5實際值5.5 A4維護5 5.5A4維護5.5.1跳閘計數器路徑：實際值×A4維護跳閘計數器n跳閘計數器n[ENTER]了解更多跳閘總數：0范圍：0至50000不完整序列跳閘：0范圍：0到50000由降壓啟動功能輸入開關跳閘引起：0范圍0到50000由于遠程、速度、減載、壓力、振動或通用開關跳閘功能轉速表跳閘：0量程0到50000。由編程為轉速計過載跳閘的數字輸入引起：0范圍：0至50000短路跳閘：0范圍0至50000機械堵塞跳閘：0量程0至50000欠電流跳閘：0幅度0至50000電流不平衡跳閘：達到50000，所有計數器復位。可使用S1 469 SETUP（設置）×CLEAR DATA（清除數據）×CLER TRIP COUNTERS（清除跳閘計數器）設定點清除該信息。5.5.2通用計數器路徑：實際值×A4維護×通用計數器469個通用計數器中的兩個計數電機啟動次數或啟動嘗試次數，以及一段時間內為啟動給定電機而執行的緊急重啟次數。在排除電機故障時，這可能是有用的信息。當這些計數器中的任何一個達到50000時，該計數器將重置為0。該信息可通過S1 469 SETUP（設置）×INSTALLATION（安裝）×RESET MOTOR information（重置電機信息）設定點清除。469個常規計數器中的另一個計數器將統計一段時間內執行的啟動器操作數。每當電機停止時，無論是跳閘還是正常停止，該計數器都會遞增
Starting will be blocked until there is sufficient thermal capacity. 5.4.2 AVERAGE MOTOR LOAD PATH: ACTUAL VALUES ?× A3 LEARNED DATA ?× AVERAGE MOTOR LOAD The 469 can learn the average motor load over a period of time. This time is specified by the S1 469 SETUP ?× PREFERENCES ?× AVERAGE MOTOR LOAD CALC. PERIOD setpoint (default 15 minutes). The calculation is a sliding window and is ignored during motor starting. n MOTOR STARTING n [ENTER] for more LEARNED ACCELERATION TIME: 0.0 s Range: 0.0 to 200.0 sec. LEARNED STARTING CURRENT: 0 A Range: 0 to 50000 A LEARNED STARTING CAPACITY: 0% used Range: 0 to 100% LAST ACCELERATION TIME: 0.0 s Range: 0.0 to 200.0 sec. LAST STARTING CURRENT: 0 A Range: 0 to 50000 A LAST STARTING CAPACITY: 0% used Range: 0 to 100% n AVERAGE MOTOR LOAD n [ENTER] for more AVERAGE MOTOR LOAD LEARNED: 0.00 x FLA Range: 0.00 to 20.00 ENTER ESCAPE e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE ENTER ESCAPE e e GE Multilin 469 Motor Management Relay 5-17 5 ACTUAL VALUES 5.4 A3 LEARNED DATA 5 5.4.3 RTD MAXIMUMS PATH: ACTUAL VALUES ?× A3 LEARNED DATA ?× RTD MAXIMUMS The 469 will learn the maximum temperature for each RTD. This information can be cleared using the S1 469 SETUP ?× CLEAR DATA ?× CLEAR RTD MAXIMUMS setpoint. If no RTDs are programmed in S8 RTD TEMPERATURE, the following flash message will appear when an attempt is made to enter this group of messages. n RTD MAXIMUMS n [ENTER] for more RTD #1 MAX. TEMP.: 40°C Range: –50 to 250°C, No RTD (open), ---- (shorted). Seen only if at least 1 maximum values of the analog inputs since they were last cleared. This information can be cleared with the S1 469 SETUP ?× CLEAR DATA ?× CLEAR ANALOG I/P MIN/MAX setpoint. When the data is cleared, the present value of each analog input will be loaded as a starting point for both minimum and maximum. The name of the input and the units will reflect those programmed for each input. If no Analog Inputs are programmed in S12 ANALOG I/O, the following flash message will appear when an attempt is made to enter this group of messages. n ANALOG IN MIN/MAX n [ENTER] for more ANALOG I/P 1 MIN: O Units Range: –50000 to 50000. Not seen if Analog Input is set as None. Reflects the Analog Input Name as programmed ANALOG I/P 1 MAX: 0 Units Range: –50 to 250°C, No RTD (open), ---- (shorted). Not seen if RTD set to None; reflects RTD Name as programmed ANALOG I/P 2 MIN: O Units Range: –50 to 250°C, No RTD (open), ---- (shorted). Not seen if RTD set to None; reflects RTD Name as programmed ANALOG I/P 2 MAX: 0 e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE GE Multilin 469 Motor Management Relay 5-19 5 ACTUAL VALUES 5.5 A4 MAINTENANCE 5 5.5A4 MAINTENANCE 5.5.1 TRIP COUNTERS PATH: ACTUAL VALUES ?× A4 MAINTENANCE ? TRIP COUNTERS n TRIP COUNTERS n [ENTER] for more TOTAL NUMBER OF TRIPS: 0 Range: 0 to 50000 INCOMPLETE SEQUENCE TRIPS: 0 Range: 0 to 50000 Caused by the Reduced Voltage Start feature INPUT SWITCH TRIPS: 0 Range: 0 to 50000 Caused by Remote, Speed, Load Shed, Pressure, Vibration, or General Purpose Switch Trip features TACHOMETER TRIPS: 0 Range: 0 to 50000. Caused by Digital Input programmed as Tachometer OVERLOAD TRIPS: 0 Range: 0 to 50000 SHORT CIRCUIT TRIPS: 0 Range: 0 to 50000 MECHANICAL JAM TRIPS: 0 Range: 0 to 50000 UNDERCURRENT TRIPS: 0 Range: 0 to 50000 CURRENT UNBALANCE TRIPS: reaches 50000, all counters reset. This information can be cleared using the S1 469 SETUP ?× CLEAR DATA ?× CLEAR TRIP COUNTERS setpoint. 5.5.2 GENERAL COUNTERS PATH: ACTUAL VALUES ?× A4 MAINTENANCE ?× GENERAL COUNTERS Two of the 469 general counters count the number of motor starts or start attempts and the number of Emergency Restarts performed to start a given motor over time. This may be useful information when troubleshooting a motor failure. When either of these counters reaches 50000, that counter will reset to 0. This information can be cleared with the S1 469 SETUP ?× INSTALLATION ?× RESET MOTOR INFORMATION setpoint. Another of the 469 General counters will count the number of starter operations performed over time. This counter is incremented any time the motor is stopped, either by a trip or normal stop
