HONEYWELL CC-TAIX11工控備件機器人模塊
，輸出繼電器必須斷電，因此，它們將處于非操作狀態。拉出箱中的短桿確保469拉出時不會發生跳閘或報警。然而，R6服務輸出將指示469已被抽出。4.5.2繼電器復位模式路徑：設定點×S4輸出繼電器繼電器復位模式鎖定跳閘或報警可隨時復位，前提是導致跳閘或報警的條件不再存在。一旦條件不再存在，未鎖定跳閘和報警將自動重置。如果可以重置任何條件，則“重置可能”LED將點亮。鎖定時間到期且跳閘復位后，所有塊啟動功能自動復位。其他繼電器可編程為All reset（所有重置），這允許從前鍵盤或遠程重置開關輸入或通信端口進行重置。可選地，繼電器1至6可編程為通過“僅遠程重置”（通過遠程重置開關輸入或通信端口）或“僅鍵盤重置”（僅通過繼電器鍵盤重置）進行重置。不得將跳閘或報警元件分配給兩個輸出繼電器，其中一個僅限遠程復位，另一個僅為鍵盤復位。如果發生這種情況，跳閘或報警將無法恢復。例如，嚴重跳閘（如短路和接地故障）可分配給R2輔助繼電器，以便只能通過遠程復位端子（D18和D23）或通信端口進行復位。遠程復位端子應連接到鑰匙開關，以便只有授權人員才能重設此類嚴重跳閘。?僅將短路和接地故障分配給R2輔助繼電器?將R2輔助編程為“僅遠程重置”n繼電器重置模式n[ENTER]以獲取更多R1跳閘：所有重置范圍：所有重置，僅遠程重置，僅鍵盤重置R2輔助：所有重置范圍：所有重置，僅鍵盤重置R4警報：所有重置范圍：所有重置，僅遠程重置，僅鍵盤重置R5塊啟動：自動重置范圍：N/A R6維修：所有重置：所有重置、僅遠程重置，鍵盤重置僅輸入退出（ENTER ESCAPE）信息退出（MESSAGE ESCAPE MESSAGE ESCAPE）消息退出（MESTAGE ESCAPE MESSAGE ESCAPE）警告GE Multilin 469電機管理繼電器4-27 4設定點4.5 S4輸出繼電器4 4.5.3強制輸出繼電器路徑：設定點×S4輸出繼電器×強制輸出繼電器輸出繼電器可以在靜態或動態模式下獨立強制。在靜態模式下，只要所選繼電器處于“啟用”狀態，它就會運行。只有當用戶輸入“禁用”時，所選繼電器才會復位。在動態模式下，用戶指定操作時間（1到300秒），所選繼電器將在指定的持續時間內運行。當所選繼電器輸出由于跳閘或報警條件而已激活時，當469處于啟動塊狀態時，或當469未運行時，不允許強制輸出繼電器選項。重要提示：強制繼電器將超越任何跳閘或報警條件。（即，當繼電器被強制并發生跳閘時，當跳閘條件被重置時，繼電器仍將被啟用）。469中的控制功率損失將重置所有強制繼電器。n強制輸出繼電器n[ENTER]了解更多強制跳閘（R1）繼電器：禁用范圍：禁用，啟用強制跳閘繼電器持續時間：靜態范圍：靜態，1至300秒，步長為1 FORCE AUX1（R2）繼電器：停用范圍：禁用，啟用的力AUX2繼電器持續時間：靜態范圍：靜態，1到300秒，步長為1力警報（R4）繼電器：禁用范圍：禁用，啟用的力警報繼電器持續時間；靜態范圍：靜止，1到300s，步長為力阻止（R5）繼電器：停用范圍：禁用，1至300秒，步進為1 ENTER ESCAPE（輸入退出）
, the output relays must be de-energized and therefore, they will be in their non-operated state. Shorting bars in the drawout case ensure that when the 469 is drawn out, no trip or alarm occurs. The R6 Service output will however indicate that the 469 has been drawn out. 4.5.2 RELAY RESET MODE PATH: SETPOINTS ?× S4 OUTPUT RELAYS ? RELAY RESET MODE A latched trip or alarm may be reset at any time, providing that the condition that caused the trip or alarm is no longer present. Unlatched trips and alarms will reset automatically once the condition is no longer present. If any condition may be reset, the Reset Possible LED will be lit. All Block Start features reset automatically when the lockout time has expired and the trip has been reset. The other relays may be programmed to All Resets which allows reset from the front keypad or the remote reset switch input or the communications port. Optionally, relays 1 through 6 may be programmed to reset by the "Remote Reset Only" (by the remote reset switch input or the communications port) or "Keypad Reset Only" (reset only by relay keypad). NO trip or alarm element must EVER be assigned to two output relays where one is Remote Reset Only and the other is Keypad Reset Only. The trip or alarm will be unresettable if this occurs. For example, serious trips such as Short Circuit and Ground Fault may be assigned to the R2 Auxiliary relay so that they can only be reset via the remote reset terminals (D18 and D23) or the communication port. The remote reset terminals should be connected to a keyswitch so that only authorized personnel could reset such a critical trip. ? Assign only Short Circuit and Ground Fault to the R2 Auxiliary relay ? Program R2 AUXILIARY to "Remote Reset Only" n RELAY RESET MODE n [ENTER] for more R1 TRIP: All Resets Range: All Resets, Remote Reset Only, Keypad Reset Only R2 AUXILIARY: All Resets Range: All Resets, Remote Reset Only, Keypad Reset Only R3 AUXILIARY: All Resets Range: All Resets, Remote Reset Only, Keypad Reset Only R4 ALARM: All Resets Range: All Resets, Remote Reset Only, Keypad Reset Only R5 BLOCK START: Auto-Reset Range: N/A R6 SERVICE: All Resets Range: All Resets, Remote Reset Only, Keypad Reset Only ENTER ESCAPE e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE WARNING GE Multilin 469 Motor Management Relay 4-27 4 SETPOINTS 4.5 S4 OUTPUT RELAYS 4 4.5.3 FORCE OUTPUT RELAY PATH: SETPOINTS ?× S4 OUTPUT RELAYS ?× FORCE OUTPUT RELAY The output relays can be independently forced in static or dynamic mode. In static mode the selected relay will operate as long as it is in the "Enabled" state. Only when the user enters "Disabled" will the selected relay reset. In dynamic mode the user specifies the operate time (1 to 300 seconds) and the selected relay will operate for the specified duration. The FORCE OUTPUT RELAY option is NOT allowed when the selected relay output is already active due to trip or alarm condition, when the 469 is in start block condition, or when the 469 is not in service. IMPORTANT NOTE: The forced relay will override any trip or alarm conditions. (i.e. when the relay is forced and trip occurs, the relay will still be enabled when the trip condition is reset). Control power loss in the 469 will reset all forced relays. n FORCE OUTPUT RELAY n [ENTER] for more FORCE TRIP (R1) RELAY: Disabled Range: Disabled, Enabled FORCE TRIP RELAY DURATION: Static Range: Static, 1 to 300 s in steps of 1 FORCE AUX1 (R2) RELAY: Disabled Range: Disabled, Enabled FORCE AUX1 RELAY DURATION: Static Range: Static, 1 to 300 s in steps of 1 FORCE AUX2 (R3) RELAY: Disabled Range: Disabled, Enabled FORCE AUX2 RELAY DURATION: Static Range: Static, 1 to 300 s in steps of 1 FORCE ALARM (R4) RELAY: Disabled Range: Disabled, Enabled FORCE ALARM RELAY DURATION: Static Range: Static, 1 to 300 s in steps of 1 FORCE BLOCK (R5) RELAY: Disabled Range: Disabled, Enabled FORCE BLOCK RELAY OPERATION: Static Range: Static, 1 to 300 s in steps of 1 ENTER ESCAPE e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE NOTE 4-28 469 Motor Management Relay GE Multilin 4.6 S5 THERMAL MODEL 4 SETPOINTS 4 4.6S5 THERMAL MODEL 4.6.1 MOTOR
