ICS TRIPLEX T8100模塊控制器,處理器模塊
可訂購金屬演示盒用于演示或測試。例如，469-P1-LO-A20代碼指定469電機管理繼電器，具有1 a CT輸入、25至60 V DC或20至48 V AC控制電壓以及4至20 mA模擬輸出。其他附件如下所示：?469PC軟件：隨每個繼電器免費提供?演示：可安裝469單元的金屬手提箱?SR 19-1面板：單切口19“面板；SR 19-2面板：雙切口19”面板?SCI模塊：RS232至RS485轉換器盒，專為惡劣的工業環境設計?相位CT：50、75、100、150、200、250、300、350、400、500、600、750、1000?HGF3，HGF5、HGF8：用于高電阻接地系統上的靈敏接地檢測。?469 1“軸環：對于淺開關設備，將繼電器的深度減少1#3/8”?469 3”軸環：用于淺開關設備的，將繼電器深度減少3”?可選安裝套件：附加安裝支架1819-0030計量附加特征電壓抽出式外殼（便于維護/測試）電流和電流需求單過渡實際功率的降低電壓啟動控制，kW需求，kW功耗跳閘線圈監控視在功率和kVA需求閃存，便于固件更新無功功率，kvar需求，kvar消耗/發電頻率功率因數RTD轉速（RPM），帶關鍵相量輸入用戶可編程模擬輸入表1–1:469 ORDER CODES 469-S-S 469 | | | 469電機管理繼電器基本單元P1 | |電流互感器輸入：1 a相CT輔助P5 | |電流變換器輸入：5 a相CT輔LO | 25至60 V DC；20至48 V AC，48至62 Hz HI | 90至300 V DC；48至62 Hz時70至265 V AC A1 0至1 mA模擬輸出A20 4至20 mA模擬輸出1-4 469電機管理繼電器GE Multilin 1.2規范1簡介1.2規范1.2.1 469規范電源選項：LO/HI（必須隨訂單指定）LO范圍：DC：20至60 V DC AC：48至62赫茲時20至48 V AC高范圍：DC:90至300 V DC AC:70至65 V AC功率：45 VA（最大值），25 VA（典型值）正常工作時間，無電源電壓：30 ms FUSE（HI和LO VOLT）額定電流：跳閘線圈監控適用電壓：20至300 V DC/V AC涓流電流：2至5 mA模擬電流輸入電流輸入：0至1 mA、0至20mA或4至20 mA（設定值）輸入阻抗：226? ±10%轉換范圍：0至21 mA精度：滿量程的±1%類型：無源模擬輸入電源：+24 V DC，100 mA最大響應時間：≤100 ms通信端口RS232端口：1，前面板，非隔離RS485端口：2，以36 Vpk波特率隔離在一起：RS485:300、1200、2400、4800、9600、19200 RS232:9600奇偶校驗：無、奇數、，偶數協議：Modbus?RTU/半雙工注釋GE Multilin 469電機管理繼電器1-5 1簡介1.2規格1模擬電流輸出類型：有效范圍：4至20 mA，0至1 mA（必須隨訂單指定）精度：滿量程的±1%最大負載：4至20mA輸入：1200? 0至1 mA輸入：10 k? 隔離：36 Vpk（與RTD和模擬輸入隔離）4個可分配輸出：A相電流、B相電流、C相電流、3相平均電流、接地電流、AN相（AB）電壓、BN相（BC）電壓、CN相（CA）電壓、三相平均電壓、最熱定子RTD、最熱軸承RTD、最高溫其他RTD、RTD#1至12、功率因數、3相實際功率（kW）、，三相視在功率（kVA）、三相無功功率（kvar）、所用熱容量、繼電器鎖定時間、電流需求、kvar需求、kW需求、kVA需求、電機負載、扭矩過載
A metal demo case may be ordered for demonstration or testing purposes. For example, the 469-P1-LO-A20 code specifies a 469 Motor Management Relay with 1 A CT Inputs, 25 to 60 V DC or 20 to 48 V AC control voltage, and 4 to 20 mA Analog Outputs. Other accessories are shown below: ? 469PC Software: Provided free with each relay ? DEMO: Metal Carry Case in which 469 unit may be mounted ? SR 19-1 PANEL: Single cutout 19" panel; SR 19-2 PANEL: Dual cutout 19" panel ? SCI MODULE: RS232 to RS485 converter box designed for harsh industrial environments ? Phase CT: 50, 75, 100, 150, 200, 250, 300, 350, 400, 500, 600, 750, 1000 ? HGF3, HGF5, HGF8: For sensitive ground detection on high resistance grounded systems. ? 469 1" Collar: For shallow switchgear, reduces the depth of the relay by 1 #3/8" ? 469 3" Collar: For shallow switchgear, reduces the depth of the relay by 3" ? Optional Mounting Kit: Additional mounting support 1819-0030 METERING ADDITIONAL FEATURES Voltage Drawout case (for ease of maintenance/testing) Current and amps demand Reduced voltage starting control for single transition Real power, kW demand, kW power consumption Trip coil supervision Apparent power and kVA demand Flash memory for easy firmware updates Reactive power, kvar demand, kvar consumption/generation Frequency Power Factor RTD Speed in RPM with a key phasor input User-programmable analog inputs Table 1–1: 469 ORDER CODES 469 — S — S — S 469 | | | 469 Motor Management Relay Base Unit P1 | | Current Transformer Inputs: 1 A Phase CT Secondaries P5 | | Current Transformer Inputs: 5 A Phase CT Secondaries LO | 25 to 60 V DC; 20 to 48 V AC at 48 to 62 Hz HI | 90 to 300 V DC; 70 to 265 V AC at 48 to 62 Hz A1 0 to 1 mA Analog Outputs A20 4 to 20 mA Analog Outputs 1-4 469 Motor Management Relay GE Multilin 1.2 SPECIFICATIONS 1 INTRODUCTION 1 1.2SPECIFICATIONS 1.2.1 469 SPECIFICATIONS POWER SUPPLY Options: LO / HI (must be specified with order) LO Range: DC: 20 to 60 V DC AC: 20 to 48 V AC at 48 to 62 Hz Hi Range: DC: 90 to 300 V DC AC: 70 to 265 V AC at 48 to 62 Hz Power: 45 VA (max), 25 VA typical Proper operation time without supply voltage: 30 ms FUSE (HI and LO VOLT) Current rating: TRIP COIL SUPERVISION Applicable Voltage: 20 to 300 V DC / V AC Trickle Current: 2 to 5 mA ANALOG CURRENT INPUTS Current Inputs: 0 to 1 mA, 0 to 20mA or 4 to 20 mA (setpoint) Input Impedance: 226 ? ±10% Conversion Range: 0 to 21 mA Accuracy: ±1% of full scale Type: passive Analog In Supply: +24 V DC at 100 mA maximum Response Time: ≤ 100 ms COMMUNICATIONS PORTS RS232 Port: 1, Front Panel, non-isolated RS485 Ports: 2, Isolated together at 36 Vpk Baud Rates: RS485: 300, 1200, 2400, 4800, 9600, 19200 RS232: 9600 Parity: None, Odd, Even Protocol: Modbus? RTU / half duplex NOTE GE Multilin 469 Motor Management Relay 1-5 1 INTRODUCTION 1.2 SPECIFICATIONS 1 ANALOG CURRENT OUTPUT Type: Active Range: 4 to 20 mA, 0 to 1 mA (must be specified with order) Accuracy: ±1% of full scale Maximum Load: 4 to 20 mA input: 1200 ? 0 to 1 mA input: 10 k? Isolation: 36 Vpk (Isolated with RTDs and Analog Inputs) 4 Assignable Outputs: phase A current, phase B current, phase C current, 3 phase average current, ground current, phase AN (AB) voltage, phase BN (BC) voltage, phase CN (CA) voltage, 3 phase average voltage, hottest stator RTD, hottest bearing RTD, hottest other RTD, RTD # 1 to 12, Power factor, 3-phase Real power (kW), 3- phase Apparent power (kVA, 3-phase Reactive power (kvar), Thermal Capacity Used, Relay Lockout Time, Current Demand, kvar Demand, kW Demand, kVA Demand, Motor Load, Torque OVERLOAD
