ICS TRIPLEX T8223自動化模塊備件
視在功率峰值視在功率其他：模擬輸入1、2、3和4轉速表1。469PC運行并建立通信后，選擇“實際”>“趨勢”菜單項以打開趨勢窗口。2.單擊設置進入圖形屬性頁面。3.通過每個描述旁邊的下拉菜單選擇要顯示的圖形。根據需要更改“顏色”、“樣式”、“寬度”、“組號”和“樣條線”選擇。為要一起縮放的所有參數選擇相同的Group#。4.單擊保存保存圖形屬性，單擊確定關閉窗口。圖8–6：圖表屬性第8-12 469頁電機管理繼電器GE Power Management 8.3使用469PC 8 469 PC軟件8 5。通過下拉菜單選擇采樣率，單擊要顯示的圖形的復選框，然后選擇RUN開始趨勢采樣。圖8-7：趨勢6。趨勢文件設置按鈕可用于將圖形數據寫入標準電子表格格式。確保選中將趨勢數據寫入上述文件復選框，且采樣率至少為5秒。圖8–8：趨勢文件設置復選框切換復選框以查看所需的圖形。按鈕打印、設置（編輯圖形屬性）放大、縮小光標行要移動行，請將鼠標指針移動到光標行上。單擊并按住鼠標左鍵并將光標線拖動到新位置MODE SELECT單擊這些按鈕可查看光標線1、光標線2、，或圖形LEVEL的Delta（差值）值顯示活動光標線波形處的圖形值來自469繼電器GE Power Management 469 Motor Management relay 8-13 8 469 PC SOFTWARE 8.3使用469PC 8 8.3.8波形捕獲469PC軟件可用于捕獲行程瞬間469的波形。最多可捕獲64個周期，觸發點可調整到設定周期內的任何位置。通過緩沖/循環權衡，最多可緩沖（存儲）16個波形。捕獲的波形為：?相電流A、B和C?差分電流A、A和C?接地電流?相電壓A-N、B-N和C-N 1。469PC運行并建立通信后，選擇實際>波形捕獲菜單項以打開波形捕獲窗口。2.將出現最后469次跳閘的A相電流波形。此行程的日期和時間顯示在窗口頂部。紅色垂直線表示繼電器的觸發點。3.按下設置按鈕進入圖形屬性頁面。通過選擇每個圖形描述旁邊的下拉菜單，對要顯示的圖形進行編程。根據需要更改“顏色”、“樣式”、“寬度”、“組號”和“樣條線”選擇。為要一起縮放的所有參數選擇相同的Group#。圖8-9：圖形屬性頁–波形捕獲4。單擊保存以存儲這些圖形屬性，然后單擊確定以關閉此窗口。5.選中相應的復選框，選擇要顯示的圖形。6.保存按鈕可用于在屏幕上存儲當前圖像，打開按鈕可用于調用保存的圖像。“打印”將窗口復制到系統打印機。8-14 469電機管理繼電器GE電源管理8.3使用469PC 8 469 PC軟件8圖8-10：波形捕獲模式選擇點擊這些按鈕查看光標1、光標2、，或圖形觸發器的Delta（差值）值單擊以手動觸發和捕獲波形DATE/TIME顯示跳閘的日期和時間觸發器代理顯示跳閘原因WAVEFORM 469繼電器LEVEL的波形數據在實線處顯示圖形的值
Apparent Power Peak Apparent Power Others: Analog Inputs 1, 2, 3, and 4 Tachometer 1. With 469PC running and communications established, select the Actual > Trending menu item to open the trending window. 2. Click Setup to enter the Graph Attribute page. 3. Select the graphs to be displayed through the pull-down menu beside each Description. Change the Color, Style, Width, Group#, and Spline selection as desired. Select the same Group# for all parameters to be scaled together. 4. Click Save to store the graph attributes and OK to close the window. Figure 8–6: GRAPH ATTRIBUTE PAGE 8-12 469 Motor Management Relay GE Power Management 8.3 USING 469PC 8 469 PC SOFTWARE 8 5. Select the Sample Rate through the pull-down menu, click the checkboxes of the graphs to be displayed, and select RUN to begin the trending sampling. Figure 8–7: TRENDING 6. The Trending File Setup button can be used to write graph data to a standard spreadsheet format. Ensure that the Write trended data to the above file checkbox is checked and that the Sample Rate is a minimum of 5 seconds. Figure 8–8: TRENDING FILE SETUP CHECK BOXES Toggle the Check Box to view the desired graphs. BUTTONS Print, Setup (to edit Graph Attributes) Zoom In, Zoom Out CURSOR LINES To move lines, move mouse pointer over the cursor line. Click and hold the left mouse button and drag the cursor line to the new location MODE SELECT Click on these buttons to view Cursor Line 1, Cursor Line 2, or Delta (difference) values for the graph LEVEL Displays the value of the graph at the active Cursor Line WAVEFORM The trended data from the 469 relay GE Power Management 469 Motor Management Relay 8-13 8 469 PC SOFTWARE 8.3 USING 469PC 8 8.3.8 WAVEFORM CAPTURE The 469PC software can be used to capture waveforms from the 469 at the instant of a trip. A maximum of 64 cycles can be captured and the trigger point can be adjusted to anywhere within the set cycles. A maximum of 16 waveforms can be buffered (stored) with the buffer/cycle trade-off. The waveforms captured are: ? Phase Currents A, B, and C ? Differential Currents A, B, and C ? Ground Current ? Phase Voltages A-N, B-N, and C-N 1. With 469PC running and communications established, select the Actual > Waveform Capture menu item to open the Waveform Capture window. 2. The waveform of Phase A current of the last 469 trip will appear. The date and time of this trip is displayed on the top of the window. The RED vertical line indicates the trigger point of the relay. 3. Press the Setup button to enter the Graph Attribute page. Program the graphs to be displayed by selecting the pull down menu beside each Graph Description. Change the Color, Style, Width, Group#, and Spline selection as desired. Select the same Group# for all parameters to be scaled together. Figure 8–9: GRAPH ATTRIBUTE PAGE – WAVEFORM CAPTURE 4. Click Save to store these graph attributes then OK to close this window. 5. Select the graphs to display by checking the appropriate checkboxes. 6. The Save button can be used to store the current image on the screen, and Open can be used to recall a saved image. Print will copy the window to the system printer. 8-14 469 Motor Management Relay GE Power Management 8.3 USING 469PC 8 469 PC SOFTWARE 8 Figure 8–10: WAVEFORM CAPTURE MODE SELECT Click on these buttons to view Cursor 1, Cursor 2, or Delta (difference) values for the graph TRIGGER Click to manually trigger and capture waveforms DATE/TIME Displays the date and time of the trip TRIGGER AGENT Displays the cause of the trip WAVEFORM The waveform data from the 469 relay LEVEL Displays the value of the graph at the solid
