IS220PPRAS1B工控備件機器人模塊
?安裝說明是產品的一部分，必須保存在儀器附近，熟練人員隨時可以使用。?在開始任何工作之前，熟練人員必須仔細閱讀并理解安裝說明。?公告836P-N壓力變送器測量和監測絕對壓力和表壓。該裝置采用最先進的技術安全制造，符合適用要求和EC指令。然而，如果使用不當或用于指定用途以外的任何用途，則可能會造成危險。?安裝和調試需要合格人員。不遵守規定會導致人身傷害或設備損壞。?安裝過程中，確保儀器和測量點的密封面清潔無損壞。?安全安裝注意事項：在安裝、調試和操作之前，確保根據測量范圍、設計和特定測量條件選擇了合適的壓力變送器。合格人員合格人員是指根據其技術培訓、測量和控制技術知識以及國家特定法規、現行標準和指令的經驗和知識，能夠實施所述工作并獨立識別潛在危險的人員。規格主題頁更改摘要1規格1尺寸[mm（in.）]3接線圖3配套電纜3工藝連接3調試3密封類型4拆卸和處理4輸出信號信號負載4…20 mA≤電源-8V/0.02 A電源總電流消耗8…30V DC信號電流，最大25 mA重要信息壓力變送器的電源必須通過符合UL/EN/IEC 61010-1第9.3節的能量限制電路，或符合UL/EN/IEC 60950-1的LPS，或符合UL-1310/UL1585（NEC或CEC）的2級。電壓源必須適用于2000米（6561.66英尺）以上的操作，并且壓力變送器應在該高度使用。2出版物836P-IN002B-EN-P-2017年12月非顯示固態壓力變送器規范（續）測量范圍表壓棒測量范圍性能特性參考操作條件（根據IEC 61298-1）操作條件：環境負載模擬信號大氣壓力860…1060毫巴沉降時間<4 ms濕度45…75%r.h。中溫開關開啟時間<15 ms安裝位置根據需要量程反極性保護模擬+vs。模擬-非線性≤量程的±0.5%抗振性10 g（0.35 oz）（IEC 60068-2-6，諧振下）入口保護（根據IEC60529）IP67–M12x1 4針出版物836P-IN002B-EN-P-2017年12月3非顯示固態壓力變送器尺寸[mm（in.）]1/4 in.NPT內螺紋1/4 in。NPT外螺紋工藝連接調試制造機械連接?安裝時，確保儀表和測量點的密封面清潔無損壞。?只能使用合適的工具通過扳手平面將儀器擰入或擰下至規定的扭矩。正確的扭矩取決于工藝連接和所用墊圈的尺寸（形狀/材料）。擰緊或擰下壓力變送器時，不要將外殼用作接觸面。?小心不要穿線。?最大扭矩為50 N·m（442.54 lb·in）。配套電纜.
? The installation instructions are part of the product and must be kept in the immediate vicinity of the instrument and readily accessible to skilled personnel at any time. ? Skilled personnel must have carefully read and understood the installation instructions, before any work begins. ? The Bulletin 836P-N pressure transmitter measures and monitors absolute and gauge pressures. The device has been safely built with state-of-the-art technology and meets the applicable requirements and EC directives. It can, however, be a source of danger if used incorrectly or for anything other than the designated use. ? Qualified individuals are required for installation and commissioning. Failure to comply results in personal injury or equipment damage. ? During mounting, make sure that the sealing faces at the instrument and the measuring point are clean and undamaged. ? Safety Installation Considerations: Before installation, commissioning, and operation, be sure that the appropriate pressure transmitter has been selected in terms of measuring range, design, and specific measuring conditions. Qualified Personnel Qualified personnel are understood to be personnel who, based on their technical training, knowledge of measurement and control technology, and on their experience and knowledge of the country-specific regulations, current standards and directives, are capable of implementing the work that is described and independently recognize potential hazards. Specifications Topic Page Summary of Changes 1 Specifications 1 Dimensions [mm (in.)] 3 Wiring Diagrams 3 Mating Cables 3 Process Connection 3 Commissioning 3 Types of Sealing 4 Dismounting and Disposal 4 Output Signals Signal Load 4…20 mA ≤ power supply -8V/0.02 A Power Supply Power Supply Total Current Consumption 8…30V DC Signal current, maximum 25 mA IMPORTANT The power supply for the pressure transmitter must be made via an energy limited electrical circuit in accordance with section 9.3 of UL/EN/IEC 61010-1, or an LPS per UL/EN/IEC 60950-1,or class 2 in accordance with UL-1310/UL1585(NEC or CEC). The voltage supply must be suitable for operation above 2,000 m (6561.66 ft) and should the pressure transmitter be used at this altitude. 2 Publication 836P-IN002B-EN-P - December 2017 Non-display Solid-state Pressure Transmitter Specifications (Continued) Measuring Ranges Gauge Pressure bar Measuring Range Performance Characteristics Reference Operation Conditions (per IEC 61298-1) Operating Conditions: Environment Load Analog signal Atmospheric pressure 860…1060 mbar Settling time < 4 ms Humidity 45…75% r. h. Medium temperature Switch on time < 15 ms Mounting position As required Accuracy of span Reverse polarity protection Analog + vs. Analog - Non-linearity ≤ ± 0.5% of span Vibration resistance 10 g (0.35 oz) (IEC 60068-2-6, under resonance) Ingress protection (per IEC60529) IP67 – M12x1 4 pin Publication 836P-IN002B-EN-P - December 2017 3 Non-display Solid-state Pressure Transmitter Dimensions [mm (in.)] 1/4 in. NPT Female 1/4 in. NPT Male Process Connection Commissioning Making the Mechanical Connection ? While mounting, make sure that the sealing faces at the instrument and the measuring point are clean and undamaged. ? Only screw or unscrew the instrument via the spanner flats and to the prescribed torque with an appropriate tool. The correct torque depends on the dimensions of the process connection and the gasket used (form/material). When screwing or unscrewing the pressure transmitter, do not use the housing as contact surface. ? Be careful not to cross-thread. ? Max torque is 50 N·m (442.54 lb·in). Mating Cables
