IS220PPRFH1A 336A4940CSP20工控自動化卡件
和羅克韋爾軟件是股份有限公司的商標。商標不屬于其各自公司的財產。羅克韋爾Otomasyon Ticaret A.?.，Kar Plaza伊什默凱茲E Blok Kat:6 34752伊澤倫克，伊斯坦布爾，電話：+90（216）5 美國印刷安裝說明1。用3/32 in.六角套筒扳手松開夾緊環上的螺釘。2.將編碼器滑動到配合軸上，直到系繩安裝件或防轉銷靠在機器表面上。編碼器應在軸上自由滑動；如果沒有，不要強行。檢查軸有無干涉，如鑿痕、毛刺、銹蝕或尺寸。如果已經存在安裝孔或防轉銷擋塊，則繼續執行步驟6。3.標記安裝孔和/或防轉銷止動位置。4.滑下編碼器。鉆孔并輕敲標記孔，以接受0.375 in.x 16（系繩選項B或C）或0.5 in.x 13（系繩選擇A）螺栓。5.將編碼器滑回軸中，直到系繩安裝件或防轉銷靠在機器表面上。6.用0.375英寸或0.5英寸螺栓連接編碼器。7.將夾緊環擰緊至8英寸磅。8.根據“電氣連接”下的表格進行電氣連接。施加規定電壓（參見本出版物第1頁“選擇”下的表“e”）。重要事項確保配合軸倒角且無油脂。重要事項擰緊螺栓時，不要對系繩支架施加壓力。重要事項接線必須符合國家電氣規范和適用的地方規范和條例。支持使用以下資源訪問支持信息。文檔反饋您的意見將幫助我們更好地滿足您的文檔需求。如果您對如何改進本文檔有任何建議， 查找相關固件的幫助。
And Rockwell Software are trademarks of Co., Ltd. Trademarks are not the property of their respective companies. Rockwell Otomasyon Ticaret A. ?., Kar Plaza Ishmerkaz E Blok Kat: 6 34752 Isserlenk, Istanbul, Tel:+90 (216) 5 US Printed Installation Instructions 1. Loosen the screws on the clamping ring with a 3/32 inch hex socket wrench. 2. Slide the encoder onto the mating shaft until the tether mount or anti rotation pin rests against the machine surface. The encoder shall slide freely on the shaft; If not, don't force it. Check the shaft for interference, such as gouges, burrs, rust, or dimensions. If the mounting hole or the anti rotation pin stop already exists, proceed to step 6. 3. Mark the mounting hole and/or the stop position of the anti rotation pin. 4. Slide down the encoder. Drill and tap the marked holes to accept 0.375 in. x 16 (lanyard option B or C) or 0.5 in. x 13 (lanyard option A) bolts. 5. Slide the encoder back into the shaft until the tether mount or anti rotation pin rests against the machine surface. 6. Connect the encoder with 0.375 inch or 0.5 inch bolts. 7. Tighten the clamping ring to 8 inch pounds. 8. Make electrical connections according to the table under "Electrical connections". Apply the specified voltage (see Table "e" under "Selection" on page 1 of this publication). It is important to ensure that the mating shaft is chamfered and free of grease. IMPORTANT Do not apply pressure to the tether bracket when tightening the bolts. Important wiring must comply with national electrical codes and applicable local codes and regulations. Support uses the following resources to access support information. Document feedback will help us better meet your document needs. If you have any suggestions on how to improve this document, look for help with the relevant firmware.
