IS220PTCCH1B DCS卡件
選擇凸輪以實現期望的目標工作臺。注意它們是位于白色側還是黑色側。4.如果需要或需要，使用下表將接觸塊簡化為最簡單、最緊湊的形式：接觸塊簡化規則（1）800T-XA替換（1）800 T-XD1&（1）80 T-XD2（1）100 T-XA1替換（1（1）200 T-XD1和（1）300 T-XD4（1）400 T-XA7替換（1（1） 800T-XD1（1）800T-XD6（迷你型）取代（1）800 T-XD2 5。訂購操作員和接觸塊作為組件。注意-操作員目錄號由操作員前綴和凸輪代碼組成。從步驟#1從步驟#2示例：800T-J2KA1此外，請確保使用800T前綴按目錄號訂購接觸塊。示例：800T-XA或800T-XD1，而不僅僅是XA或XD1。5A中。或作為完整的工廠組裝設備訂購。設備目錄號由操作員前綴、凸輪代碼和接觸塊配置后綴組成。有關此后綴的詳細信息，請參閱第3頁。示例：800T-J2KA1ADXX選擇開關選擇步驟公告800T油密選擇開關產品數據8使用標準旋鈕和三個電路選擇一個保持的三位“手動-自動”選擇開關，如圖所示：XOX OOX XOO 1。從第9頁的表1中選擇運算符前綴。800T-J2。從第9頁的表2中選擇凸輪和索引代碼。代碼KC1或KC7同樣有效。本例使用KC1。800T-J2KC1 3。根據目標表選擇接觸塊。X O O=800T-XD2（黑色）O O X=800T-XD1（黑色）X O X=800 T-XD3（白色）4。通過將800T-XD1和800T-XD2組合成800T-XA（參見第7頁），簡化黑邊。接觸塊組合為：POS#1 POS#2 800T-XD3 800T-XA黑色側白色側5。將操作員和接觸塊作為組件訂購：800T-J2KC1–步驟1和2 800T-XD3–步驟4 800T-XA–步驟4 5A。或作為工廠組裝的設備訂購：800T-J2KC1GAXX:800T-XD3（白色側）800T-XA（黑色側）空白（白色側，空白）XXAG POS#4黑色側POS#3白色側POS#2黑色側POS#1白色側有關附加后綴說明，請參閱第6頁。選擇開關選擇步驟示例公告800T油密選擇開關產品數據9表1 3位選擇開關操作員類型? 操作員功能目錄號? 標準標準顏色為黑色保持彈簧從左側返回彈簧從右側返回彈簧從左側和右側返回表2 3位選擇開關功能A c觸點塊操作員位置從正面觀察X=觸點閉合O=觸點打開u目錄編號c O凸輪和索引代碼標準選擇開關A t O編號后綴請咨詢工廠了解特殊硬幣槽操作員。? 所列目錄號不完整。從表2中添加所需的凸輪和索引代碼。? 翼桿不適合與“KE7”凸輪代碼一起使用。3位選擇開關公告800T油密選擇開關產品數據10使用旋鈕桿從左側操作員選擇3位彈簧復位，目標工作臺位于右側：1。從表1中選擇所需前綴。800T-J18 2。從表2中選擇凸輪代碼。KD7 3。識別接觸塊：XOO=800T-公告800T油密選擇開關產品數據11表3 4位選擇開關操作員類型? 操作員功能目錄號? 標準標準顏色為黑色保持彈簧從位置1返回到位置2彈簧從位置4返回到位置
selected cam to achieve the desired target table. Note whether they are located on the white side or black side. 4. Use the following table to reduce the contact blocks to their simplest and most compact form if desired or required: Contact Block Reduction Rules (1) 800T-XA replaces (1) 800T-XD1 & (1) 800T-XD2 (1) 800T-XA1 replaces (1) 800T-XD1 & (1) 800T-XD4 (1) 800T-XA7 replaces (1) 800T-XD2 & (1) 800T-XD4 (1) 800T-XA2 replaces (2) 800T-XD1 (1) 800T-XA4 replaces (2) 800T-XD2 (1) 800T-XD5 (Mini) replaces (1) 800T-XD1 (1) 800T-XD6 (Mini) replaces (1) 800T-XD2 5. Order the operator and contact blocks as components. NOTE - The operator catalog number consists of the operator prefix plus cam code. From Step # 1 From Step # 2 Example: 800T-J2KA1 Also, be sure to order the contact block(s) by catalog number using the 800T prefix. Example: 800T-XA or 800T-XD1, not XA or XD1 only. 5A. Or order as a complete factory assembled device. The device catalog number consists of the operator prefix, the cam code and the contact block configuration suffix. Refer to Page 3 for details on this suffix. Example: 800T-J2KA1ADXX Selector Switch Selection Steps Bulletin 800T Oiltight Selector Switches Product Data 8 Select a maintained 3-position “Hand-Off-Auto”selector switch with standard knob and three circuits as shown: XOX OOX XOO 1. Select an operator prefix from Table 1 on Page 9. 800T-J2 2. Select a cam and index code from Table 2 on Page 9. Code KC1 or KC7 would be equally effective. Use KC1 for this example. 800T-J2KC1 3. Select contact blocks based on the target tables. X O O = 800T-XD2 (Black) O O X = 800T-XD1 (Black) X O X = 800T-XD3 (White) 4. Simplify the Black side by combining the 800T-XD1 and 800T-XD2 into an 800T-XA (see Page 7). The contact block combination would be: POS #1 POS #2 800T-XD3 800T-XA BLACK SIDE WHITE SIDE 5. Order the operator and contact blocks as components: 800T- J2KC1 – From Steps 1 & 2 800T-XD3 – From Step 4 800T-XA – From Step 4 5A. Or order as a factory assembled device: 800T-J2KC1GAXX: 800T-XD3 (White Side) 800T-XA (Black Side) Vacant (White Side) Vacant (Black Side) XXAG POS #4 BLACK SIDE POS #3 WHITE SIDE POS #2 BLACK SIDE POS #1 WHITE SIDE See Page 6 for additional suffix explanation. Selector Switch Selection Steps Example Bulletin 800T Oiltight Selector Switches Product Data 9 Table 1 3-Position Selector Switch Operators Type of Operator ? Operator Function Catalog Number ? Standard Standard Color is Black Maintained Spring return from left Spring return from right Spring return from left and right Table 2 3-Position Selector Switch Function A c Contact Block Operator Position Viewed from Front X=Contact Closed O=Contact Open t u Catalog Number C o Cam and Index Code Standard Selector Switch a t o Number Suffixes Consult Factory for Special Coin Slot Operators. ? Catalog Numbers as listed are not complete. Add the desired Cam and Index Code from Table 2. ? Wing Levers are not suitable for use with “KE7” Cam Code. 3-Position Selector Switches Bulletin 800T Oiltight Selector Switches Product Data 10 Select a 3-position spring return from left operator with a knob lever with the target table to the right: 1. Select the desired prefix from Table 1. 800T-J18 2. Select the Cam Code from Table 2. KD7 3. Identify the contact blocks: XOO = 800T- Bulletin 800T Oiltight Selector Switches Product Data 11 Table 3 4-Position Selector Switch Operators Type of Operator ? Operator Function Catalog Number ? Standard Standard Color is Black Maintained Spring return from position 1 to position 2 Spring return from position 4 to position
