IS200TPROH1BBB系統模塊卡件
（4） 額定速度等級僅用于比較目的。使用運動分析儀為您的應用確定電機尺寸和/或Kinetix 5500驅動系統設計指南KNX-RM009出版物和Kinetix 5700驅動系統設計手冊KNX-RM010出版物中的扭矩/速度曲線。在安裝電機之前，執行這些檢查步驟，并檢查軸封、氣壓套件、聯軸器和滑輪以及電氣噪音防護指南。1.小心地從運輸容器中取出電機。有關更多信息，請參閱第3頁的起吊說明。2.目視檢查電機有無損壞。3.檢查電機框架、前輸出軸和安裝導向器是否有任何缺陷。4.立即通知承運人運輸損壞。VP H-x xxx x x-x J x x D xx電機電纜長度01=1 m（3.2 ft）連續撓性額定值03=3 m（9.8 ft）連續柔性額定值05=5 m（16.4 ft）連續彈性額定值07=7 m（22.9 ft）連續剛性額定值09=9 m（29.5 ft）標準，非撓性額定值12=12 m（39.4 ft）標準、非撓性額定15=15 m（49.2 ft）標準和非撓性額定IEC公制，帶螺紋的安裝孔：D=標準單電纜制動器2=無制動器4=24V DC制動器軸鍵J=軸鍵連接器（1）1=單SpeedTec DIN連接器0=飛線反饋C=18位絕對單圈數字編碼器（Hiperface DSL協議）Q=23位絕對多圈數字編碼器，12位二級安全信道（2）W=18位絕對多匝數字編碼器（Hiperface DSL協議）SIL 2（PLd）額定值，9位二級安全通道（3）額定轉速（4）C=2300 rpm F=4500…6600 rpm D=3000 rpm M=6700 rpm E=3300…3900 rpm T=7200…8000 rpm磁體堆疊長度（1、2、3、4個堆疊）（5）框架尺寸-螺栓圓直徑（BCD）063=63 mm 115=115 mm 075=75 mm 130=130 mm 100=100 mm 165=165 mm電壓等級A=200V B=400V系列H=衛生(4) Rated speed hierarchy is only for comparative purposes. Use Motion Analyzer to size and select motors for your application, and/or the torque/speed curves in the Kinetix 5500 Drive Systems Design Guide, publication KNX-RM009, and the Kinetix 5700 Drive Systems Design Guide, publication KNX-RM010. (5) Refer to Motor Dimensionson page 9for dimensional changes that result from the number of magnet stacks. Before You Install the Motor Perform these inspection steps and review the guidelines for shaft seals, air-pressure kits, couplings and pulleys, and electrical noise prevention. 1. Remove the motor carefully from its shipping container. See Lifting Instructions on page 3 for more information. 2. Visually inspect the motor for any damage. 3. Examine the motor frame, front output shaft, and mounting pilot for any defects. 4. Notify the carrier of shipping damage immediately. VP H - x xxx x x - x J x x D xx On Motor Cable Length 01 = 1 m (3.2 ft) continuous-flex rated 03 = 3 m (9.8 ft) continuous-flex rated 05 = 5 m (16.4 ft) continuous-flex rated 07 = 7 m (22.9 ft) continuous-flex rated 09 = 9 m (29.5 ft) standard, non-flex rated 12 = 12 m (39.4 ft) standard, non-flex rated 15 = 15 m (49.2 ft) standard, non-flex rated IEC Metric, tapped mounting hole with: D = Standard single cable Brake 2 = No Brake 4 = 24V DC Brake Shaft Key J = Shaft key Connector (1) 1 = Single SpeedTec DIN connector 0 = Flying leads Feedback C = 18-bit absolute single-turn digital encoder (Hiperface DSL protocol) Q = 23-bit absolute multi-turn digital encoder (Hiperface DSL protocol) SIL 2 (PLd) rated, 12-bit secondary safety channel (2) W = 18-bit absolute multi-turn digital encoder (Hiperface DSL protocol) SIL 2 (PLd) rated, 9-bit secondary safety channel (3) Rated Speed (4) C = 2300 rpm F = 4500…6600 rpm D = 3000 rpm M= 6700 rpm E = 3300…3900 rpm T = 7200…8000 rpm Magnet Stack Length (1, 2, 3, 4 stacks) (5) Frame Size - Bolt Circle Diameter (BCD) 063 = 63 mm 115 = 115 mm 075 = 75 mm 130 = 130 mm 100 = 100 mm 165 = 165 mm Voltage Class A = 200V B = 400V Series Type H = Hygienic
