IC695CPU315-CD工控模塊機器人備件
最低光束z2H+1 z2H+1 z 3H–區域3最高光束3n/4 3n/4 z4L–區域4最低光束z3H+1 z3H+1 z 4H–區域4最高光束n n光束計數模式0=第一光束電纜側注意：通過正確接地或分流以及使用靜電控制包裝和材料搬運產品，幫助保護控制器免受ESD的影響。通過接地、電離和使用導電和耗散靜電控制材料來耗散和中和。重要信息：只有使用懸掛檢測的應用程序才需要設置載體區域。對于其他應用程序，按“設定”按鈕跳過此步驟。8羅克韋爾自動化出版物45MLA-IN002C-EN-P-2020年8月45MLA控制器安裝說明4.超高超高輸出（Out 2）是一個離散的開關輸出，在任何光束中斷時默認激活。（默認光束oh=光束1）要設定超高級別，請將允許的最高對象放置在燈光陣列的范圍內，然后短按“設定”按鈕。狀態指示器D14現在應該保持亮起，這表明現在已經設置了允許的最高物體光束。下一個不間斷光束被設置為“哦”光束。在該設定過程結束時，如果任何以“oh”或更高開頭的光束被中斷，則超高輸出（Out 2）被激活。5.配置區域如果此時不希望配置特定區域，請按住“設定”按鈕，直到狀態指示器D14熄滅（約5秒），這表示設定過程結束。如果您希望配置感應區域（對應于輸出3…6），請短按“設定”按鈕進入?yún)^(qū)域設置并遵循以下步驟
Lowest beam z2H+1 z2H+1 z3H – Zone 3 Highest beam 3n/4 3n/4 z4L – Zone 4 Lowest beam z3H+1 z3H+1 z4H – Zone 4 Highest beam n n Beam counting mode 0 = first beam cable side ATTENTION: Help protect the controller from ESD with proper grounding or shunting and the use of static control packaging and materials handling products. Dissipate and neutralize by grounding, ionization, and the use of conductive and dissipative static control materials. IMPORTANT Setting the carrier zone is only required for applications that use over-hang detection. For other applications, press the Teach button to skip this step. 8 Rockwell Automation Publication 45MLA-IN002C-EN-P - August 2020 45MLA Controller Installation Instructions 4. Over-height The over-height output (Out 2) is a discrete on-off output that is activated by default when any beam is interrupted. (Default Beam oh = Beam 1) To teach the over-height level, place the highest allowed object in the range of the light array and then briefly press the Teach button. Status indicator D14 should now remain on, which indicates that the highest allowed object beam has now been set. The next uninterrupted beam is set as the “oh” beam. At the conclusion of this teach process, if any beam starting with “oh” and higher is interrupted, the over-height output (Out 2) is activated. 5. Configure zones If you do not wish to configure specific zones at this point, press and hold the Teach button until status indicator D14 turns off (approximately 5 seconds), which signals the end of the teach process. If you wish to configure sensing zones (corresponding to Outputs 3…6), press the Teach button briefly to enter the zone setup and follow these
