GE MIFIIPI55E10HI00 處理器模塊
24 VDC 0 VDC表12-J2引腳列表引腳信號說明備注1 0V DC電源-2+24V DC電源-3接地-4未連接未連接-5入2觸發并保持DIP開關S1（7）=0后懸傳感器DIP開關S2（7）=1 6入1未使用DIP開關S3（7）=0前懸傳感器DIP開關S1（8）=1 7出2燈陣列中斷（1）（1）或高度過高（特殊功能）0V DC=中斷的24V DC=未中斷的8輸出1懸垂0V DC=懸垂24V DC=無懸垂表13-J14引腳列表引腳信號0V DC+24V DC 1輸出3區域Z1中斷區域Z1未中斷2輸出4區域Z2中斷區域Z2未中斷3輸出5區域Z3中斷區域Z3未中斷4輸出6區域Z4中斷區域Z4未中斷表14-I/O板狀態指示器狀態指示器描述狀態含義D10區域1關閉輸出3=關閉（0V DC）綠色輸出3=打開（24V DC）D11區域2關閉輸出4=關閉（0 V DC）綠色出口4=打開（24 V DC）D12區域3關閉輸出5=關斷（0 V直流）綠色輸出5=開啟（24 V直流）D13區域4關閉輸出6=關閉（V DC）藍色輸出6=打開（24VDC）D14示教關閉非激活閃爍示教進行中橙色最后一個示教步驟羅克韋爾自動化出版物45MLA-IN002C-EN-P-2020年8月7 45MLA控制器安裝說明DIP開關設置S1 DIP開關陣列上的DIP開關1…6配置用于表15中所述的各種應用。如果未提供其他信息，這些DIP開關應保持在OFF位置。DIP開關7用于配置懸垂模式（更多信息請參見出版物10000071139），DIP開關8用于重置默認配置。一旦更改，DIP開關設置僅在電源循環后才能識別。表15詳細說明了I/O板的DIP開關設置。有關所列功能的更多信息，請參閱編程指南。默認參數表16列出了前面討論的每個參數的默認值，可以通過使用DIP開關陣列S1上的開關8進行重置，然后進行電源循環。示教過程示教功能允許您通過使用I/O擴展PCB上的按鈕配置多個功能的參數。以下各節詳細介紹了可教給傳感器的參數以及與此程序相關的步驟。
24 VDC 0 VDC Table 12 - J2 Pin Listings Pin Signal Description Remarks 1 0V DC Power — 2 +24V DC Power — 3 Ground Ground — 4 Not connected Not connected — 5 In 2 Trigger and hold DIP switch S1 (7) = 0 Overhang back sensor DIP switch S1 (7) = 1 6 In 1 Not used DIP switch S1 (7) = 0 Overhang front sensor DIP switch S1 (7) = 1 7 Out 2 Light array interrupted (1) (1) Or over-height (special function) 0V DC = interrupted 24V DC = not interrupted 8 Out 1 Overhang 0V DC = overhang 24V DC = no overhang Table 13 - J14 Pin Listings Pin Signal 0V DC +24V DC 1 Out 3 Zone Z1 interrupted Zone Z1 not interrupted 2 Out 4 Zone Z2 interrupted Zone Z2 not interrupted 3 Out 5 Zone Z3 interrupted Zone Z3 not interrupted 4 Out 6 Zone Z4 interrupted Zone Z4 not interrupted Table 14 - I/O Board Status Indicators Status Indicator Description Status Meaning D10 Zone 1 Off Out 3 = OFF (0V DC) Green Out 3 = ON (24V DC) D11 Zone 2 Off Out 4 = OFF (0V DC) Green Out 4 = ON (24V DC) D12 Zone 3 Off Out 5 = OFF (0V DC) Green Out 5 = ON (24V DC) D13 Zone 4 Off Out 6 = OFF (0V DC) Green Out 6 = ON (24V DC) D14 Teach Off Teach inactive Flashing Teach in progress Orange Last teach step Rockwell Automation Publication 45MLA-IN002C-EN-P - August 2020 7 45MLA Controller Installation Instructions DIP Switch Settings DIP switches 1…6 on the S1 DIP switch array are configured for the various applications that are described in Table 15. If no information is otherwise provided, these DIP switches should remain in the OFF position. DIP switch 7 is used to configure the overhang mode (see Publication 10000071139 for further information) and DIP switch 8 is used to reset default configuration. Once changed, DIP switch settings are only recognized after a power cycle. Table 15 details DIP switch settings for the I/O board. See the Programming Guide for further information on the listed functions. Default Parameters Table 16 lists the default values for each of the parameters that are previously discussed, that can be reset by use of switch 8 on DIP switch array S1, followed by a power cycle. Teach Process The teach function allows you to configure the parameters for a number of functions by use of a push button on the I/O extension PCB. The following sections detail the parameters that can be taught to the sensor, and the steps associated with this procedure.
