GE IS420ESWBH3A 工業自動化卡件
中斷要忽略的光束/區域，并關閉輸入IN 1。IN 1從ON變為OFF時中斷的光束決定了空白區域。可以使用DIP開關8或再次執行示教過程來重置空白區域。教學過程中的注意事項：?單個空白區域中不能有任何孔，所有光束必須中斷才能定義該區域。?第一消隱區從第一中斷射束限定為小于未被阻擋的第一射束。（DIP開關6確定波束計數方向，默認標準波束計數從陣列的電纜端開始。）如果（且僅當）第一個消隱區以波束1開始，也可以創建第二個消隱區域。該區域定義為從下一個中斷波束開始（在第一個不中斷波束之后）一直到陣列末端，而不管其他波束被中斷。?為獲得最佳結果，請確認空白區域中的所有光束均已完全阻斷。此外，如果正在創建兩個空白區域，則確認第一區域包括光束1（基于DIP開關6確定的光束計數方向）。功能描述-I/O模型圖5-I/O模型該控制器模型擴展了45MLA控制器的功能，以提供四個附加輸出信號和一個示教功能。這些輸出可以分配給光陣列上的特定區域或單個光束。引腳列表表12顯示了主連接器J2上的引腳分配。表13顯示了I/O擴展PCB上的引腳配置。狀態指示器表14顯示了I/O擴展PCB上狀態指示器D10…D14的含義。輸入2個PNP NPN PNP NPP D7 LED-電源I/O擴展PCB D3 LED輸出1個D4 LED輸出2個D6 LED輸入2個D5 LED輸入1個D13 LED D14 LED D12 LED D11 LED D10 LED RJ45連接器發射器RJ45連接器接收器D2 LED D1輸入1個電位計2個電位計1個示教按鈕可拆卸彈簧加載連接器輸入邏輯跳線S1 J2 J14輸出1個輸出2個輸入1個接地。Interrupt the beams/zones that are to be ignored and turn the input IN 1 OFF. The beams that are interrupted while IN 1 changes from ON to OFF determine the blanked zones. The blanked zones can be reset with DIP switch 8 or by doing the teach process again. Notes on the teach process: ? There cannot be any holes in a single blanked zone—all beams must be interrupted to define the zone. ? The first blanked zone is defined from the first interrupted beam to one less than the first beam that is not blocked. (DIP switch 6 determines beam counting direction, with the default standard beam counting starting from the cable end of the array.) If (and only if) the first blanked zone starts with Beam 1, a second blanked zone can also be created. The zone is defined as starting with the next interrupted beam (after the first uninterrupted beam) all the way to the end of the array, regardless of which other beams are interrupted. ? For best results, confirm that all beams in the blanked zone are completely blocked. Also, if two blanked zones are being created, confirm that the first zone includes beam 1 (based on the beam counting direction that DIP switch 6 determines). Functional Description — I/O Model Figure 5 - I/O Model This model of the controller extends the functionality of the 45MLA controller to offer four additional output signals and a teach function. These outputs can be allocated to specific zones or single beams on the light array. Pin Listings Table 12 shows the allocation of pins on the main connector, J2. Table 13 shows the allocation of pins on the I/O extension PCB. Status Indicators Table 14 shows the meaning of status indicators D10…D14 on the I/O extension PCB. In 2 PNP NPN PNP NPN D7 LED - Power I/O Extension PCB D3 LED Out 1 D4 LED Out 2 D6 LED In 2 D5 LED In 1 D13 LED D14 LED D12 LED D11 LED D10 LED RJ45 Connector Emitter RJ45 Connector Receiver D2 LED D1 LED In 1 Pot 2 Pot 1 Teach PushButton Removable Spring-Loaded Connector Input Logic Jumpers S1 J2 J14 Out 1 Out 2 In 1 In 2 n. c. Earth.
