GE IS220PAICH1A 336A4940CSP3 工控模塊機器人備件
當啟用雙掃描模式時，使用電位計1可以使檢測的最小持續時間更長。此額外的時間延遲可以從0到3.3秒不等。表10-J2引腳列表引腳信號說明備注1 0V DC電源-2+24V DC電源-3接地-4未連接未連接-5輸入2未使用-6輸入1未使用DIP開關S1（3）=0遠程示教DIP開關S2（3）=1 7輸出2錯誤0V DC=錯誤8輸出1燈陣列中斷0V DC=中斷24V DC=未中斷輸入2 PNP NPN PNP NPP D7 LED-電源D3 LED輸出1 D4LED輸出2 D6 LED輸入2 D5 LED輸入1 RJ45連接器發射器RJ45連接器接收器D2 LED輸入1電位計2電位計1可拆卸彈簧加載連接器輸入邏輯跳線S1 J2輸出1輸出2輸入1輸入2 n.c.接地。24 VDC 0 VDC表11-基本型號DIP開關設置功能DIP開關S1（0：關閉，1：打開，X：不相關）87654321默認設置0 0 0 0 00 0 0 0最大發射器功率（100%）0xxxxx00降低發射器功率（最大值的75%）0xxxxx01降低發射器功率，最大值的60%）0xxxxx10降低發射器功率輸出邏輯光操作=24V（PNP L.O.）暗操作=0V（NPN D.O.）0xx0xxxx輸出邏輯光運行=0V安裝說明教示說明基本控制器提供教示操作期間未評估的空白區域的功能。您可以在陣列的一端或兩端配置空白區域（例如，如果陣列對于應用程序來說太長）；或者在數組中間有一個空白區域（如果中間的某個區域太被忽略）。要激活示教功能，必須打開DIP開關3（并重啟控制器電源）以啟用遠程示教。啟用遠程設定后，通過打開離散輸入IN 1啟動設定過程。When the double-scan mode is enabled, the minimum duration of detection can be made even longer with the use of potentiometer one. This additional time delay can range from 0…3.3 seconds. Table 10 - J2 Pin Listings Pin Signal Description Remarks 1 0V DC Power — 2 +24V DC Power — 3 Ground Ground — 4 Not connected Not connected — 5 In 2 Not used — 6 In 1 Not used DIP switch S1 (3) = 0 Remote teach DIP switch S1 (3) = 1 7 Out 2 Error 0V DC = Error 8 Out 1 Light array interrupted 0V DC = interrupted 24V DC = not interrupted In 2 PNP NPN PNP NPN D7 LED - Power D3 LED Out 1 D4 LED Out 2 D6 LED In 2 D5 LED In 1 RJ45 Connector Emitter RJ45 Connector Receiver D2 LED D1 LED In 1 Pot 2 Pot 1 Removable Spring-Loaded Connector Input Logic Jumpers S1 J2 Out 1 Out 2 In 1 In 2 n. c. Earth. 24 VDC 0 VDC Table 11 - Basic Model DIP Switch Settings Function DIP Switch S1 (0: OFF, 1: ON, X: not relevant) 87654321 Default setting 0 0 0 0 0 0 0 0 Maximum emitter power (100%) 0xxxxx00 Reduce emitter power (75% of max) 0xxxxx01 Reduce emitter power (60% of max) 0xxxxx10 Reduce emitter power (15% of max) 0xxxxx1 1 Enable remote teach 0 x x x x 1 x x Enable double scan filter 0 x x x 1 x x x Output logic Light Operate = 24V (PNP L.O.) Dark Operate = 0V (NPN D.O.) 0xx0xxxx Output logic Light Operate = 0V (NPN L.O.) Dark Operate = 24V (PNP D.O.) 0xx1xxxx Standard beam counting direction 0x0xxxxx Reverse beam counting direction 0x1xxxxx Normal operation 0 x x x x x x x Set default 1 x x x x x x x 6 Rockwell Automation Publication 45MLA-IN002C-EN-P - August 2020 45MLA Controller Installation Instructions Teach Instructions The Basic Controller offers the ability to teach blanked zones that are not evaluated during operation. You can either configure blanked zones at one or both ends of the array (for example if the arrays are too long for the application); OR one blanked zone in the middle of the array (if an area in the middle is too be ignored). To activate the teach capability DIP switch 3 must be turned ON (and controller power cycled) to enable the remote teach. Once the remote teach is enabled, the teach process is initiated by turning the discrete input IN 1 ON.
