3500/22M 138607-01工控模塊備件
In 2 PNP NPN PNP D7 LED--Power NPN型號特定擴展PCB D3 LED Out 1 D4 LED Out 2 D6 LED In 2 D5 LED In 1 RJ45連接器發射器RJ45連接器接收器D2 LED D1 LED Gaps In 1 Out 1 Out 2 In 1 In 2 N.C.接地。24 V DC 0 V DC Pot 2 Pot 1可拆卸彈簧加載連接器輸入邏輯跳線S1 J2 J14 PHOTOSwitcher光電傳感器45MLA測量陣列和控制器請訪問我們的網站：www.ab.com/catalogs。1-163首選可用性類別。編號以粗體打印。底座PCB上的接頭J2具有以下所有控制器型號的引腳。引腳信號說明1 0V DC電源2+24V DC電源3接地4未連接未連接5…8型號特定功能（見下文）連接器J2（在基礎PCB上）上的引腳5…8具有不同的功能，適用于每個控制器型號。下表顯示了每個特定型號的引腳連接。I/O型號RS485和CAN型號引腳信號描述備注引腳信號描述注釋5輸入2觸發并保持DIP開關S1（7）=0 5輸入2觸發器并保持特殊功能懸置后傳感器DIP開關S2（7）=1 6輸入1未使用6輸入1不使用DIP開關S 1（7）=0 7輸出2光中斷0V=中斷懸置前傳感器DIP切換S1（7懸垂7出2燈陣列中斷0 V DC=中斷24 V DC=未中斷8出1懸垂0 V DC＝懸垂24 V DC＝無懸垂或超出高度（特殊功能）擴展PCB具有特定于每個單獨型號功能的連接。以下是每種型號的引腳連接。連接器標記在PCB上。I/O型號連接器J14 RS485型號連接器J16 CAN型號連接器J12和J13（RJ45）引腳信號0V DC+24V DC引腳2導線4引腳信號1輸出3區域Z1中斷區域Z1未中斷1 0V DC 0V DC 1 CAN H 2輸出4區域Z2中斷區域Z2未中斷2-Rx+2 CAN L 3輸出5區域Z3中斷區域Z3未中斷3屏蔽屏蔽3 0V DC 4輸出6區域Z4中斷Z4區未中斷4-Rx--4未連接5 B Tx+5未連接6 A Tx-6屏蔽7 0V DC 8 CAN V+PHOTOSwitcher光電傳感器45MLA測量陣列和控制器1-164請訪問我們 首選可用性類別。
In 2 PNP NPN PNP D7 LED Power NPN model specific expansion PCB D3 LED Out 1 D4 LED Out 2 D6 LED In 2 D5 LED In 1 RJ45 connector transmitter RJ45 connector receiver D2 LED D1 LED Gaps In 1 Out 1 Out 2 In 1 In 2 N.C. Ground. 24 V DC 0 V DC Pot 2 Pot 1 detachable spring loaded connector input logic jumper S1 J2 J14 PHOTOSwitcher photoelectric sensor 45MLA measurement array and controller Please visit our website: www.ab.com/catalogs. 1-163 Preferred availability category. The numbers are printed in bold. Connector J2 on the base PCB has pins for all of the following controller models. Pin signal description: 1 0V DC power supply 2+24V DC power supply 3 ground 4 not connected Not connected 5... 8 Pin 5... 8 on connector J2 (on the base PCB) with specific functions (see below) has different functions and is applicable to each controller model. The following table shows the pin connections for each specific model. I/O model RS485 and CAN model pin signal description Remarks Pin signal description Note 5 Input 2 triggers and holds DIP switch S1 (7)=0 5 Input 2 triggers and holds special functions Rear suspension sensor DIP switch S2 (7)=1 6 Input 1 Not used 6 Input 1 Not used DIP switch S 1 (7)=0 7 Output 2 Optical interrupt 0V=Interrupt Front suspension sensor DIP switch S1 (7 overhang 7 out 2 lamp array interrupt 0 V DC=interrupt 24 V DC=not interrupt 8 out 1 overhang 0 V DC=overhang 24 V DC=no overhang or over height (special function) The extended PCB has a connection specific to each individual model function. The following are the pin connections for each model. The connector is marked on the PCB. I/O model connector J14 RS485 model connector J16 CAN model connector J12 and J13 (RJ45) Pin signal 0V DC+24V DC Pin 2 Wire 4 Pin signal 1 Output 3 Area Z1 Interruption area Z1 Not interrupted 1 0V DC 0V DC 1 CAN H 2 Output 4 Area Z2 Interruption area Z2 Not interrupted 2-Rx+2 CAN L 3 Output 5 Area Z3 Interruption area Z3 Not interrupted 3 Shield shield 3 0V DC 4 Output 6 Area Z4 Interruption Z4 Area 4-Rx-4 Not connected 5 B Tx+5 Not connected 6 A Tx-6 Shield 7 0V DC 8 CAN V+PHOTOSwitcher Photoelectric Sensor 45MLA Measurement Array and Controller 1-164 Please visit us Preferred availability category.
