TRICONEX 9668-110工業備件
電源輸入
換向分解器或高分辨率輸出檢查孔，頂部和底部至插頭，直徑。直徑的通孔需要。直徑為，在直徑為的上安裝螺栓必須為帽頭式螺紋孔，最小深度軸詳全深度端銑鍵槽電機前端鐘形角半徑最大軸跳動軸端隙最大導向偏心最大端面跳動銘牌詳軸和導向公差高分辨率電機端部法蘭安裝單位：毫米和英寸反饋目錄編號描述鍵端銑鍵槽全深度無制動器無制動器，無制動器，不帶制動器的，可選，制動器等級，和增加。尺寸符合標準和。軸公差符合，扭矩增強系列，交流伺服電機出版物年月扭矩增強系列分解器和高分辨率反饋鍵最大值直徑。直徑直徑。直徑。直徑直徑。
直徑功率輸入軸詳直徑
直徑上需要通孔。直徑上的直徑安裝螺栓必須為帽頭式檢查孔，頂部和底部至堵頭螺紋孔深最小全深端銑鍵槽凹形飛邊和軸封提供換向分解器或高分辨率輸出吊鉤詳電機前端鐘形角半徑銘牌詳軸和導向公差高分辨率電機端最大軸跳動軸端隙最大導向偏心最大端面跳動法蘭安裝單位：毫米和英寸反饋目錄編號描述鍵端銑鍵槽全深度旋轉器，則和增加增加。尺寸符合標準和。軸公差
交流伺服電機出版物年月扭矩增強系列分解器和高分辨率反饋鍵最大值直徑。
Power input
Reversing resolver or high-resolution output inspection hole, top and bottom to plug, diameter. Diameter through hole is required. The installation bolt on the motor with a diameter of must be a cap type threaded hole. See full depth end milling keyway for the minimum depth shaft. The front end bell angle radius of the motor has the maximum shaft runout. The maximum shaft runout. The maximum guide eccentricity. The maximum end face runout nameplate has the shaft and guide tolerance. The installation unit of the high resolution motor end flange is mm and inch. The feedback catalog number describes that the key end milling keyway has the full depth, no brake, no brake, and no brake, Optional, brake class, and increase. The dimensions comply with the standards and. The shaft tolerance conforms to the maximum diameter of torque enhancement series, AC servo motor publication torque enhancement series resolver and high-resolution feedback key. Diameter diameter. Diameter. Diameter diameter.
Diameter See diameter for power input shaft
A through hole is required on the diameter. The diameter mounting bolts on the diameter must be hat type inspection holes, The minimum full depth end milling keyway concave flash and shaft seal from the top and bottom to the plug threaded hole depth provide reversing resolver or high-resolution output hook. See the motor front end bell angle radius nameplate. See the shaft and guide tolerance. High resolution motor end maximum shaft runout. Shaft end clearance. Maximum guide eccentricity. Maximum end face runout. Flange installation unit: mm and inch. Feedback catalog number. Description. Key end milling keyway full depth rotator. Then, and increase. The dimensions comply with the standards and. Shaft tolerance
AC Servo Motor Publications Month Torque Enhancement Series Resolver and High Resolution Feedback Keys Maximum Diameter.
