国产精品久久二区二区,熟女少妇内射日韩亚洲,久久亚洲国产成人精品无码区,GOGO熟女少妇大尺度

您的瀏覽器版本過低,為保證更佳的瀏覽體驗,請點擊更新高版本瀏覽器

以后再說X

歡迎訪問瑞昌明盛自動化設備有限公司網站!

圖片名

全國訂購熱線:
+86 15270269218E-mail:xiamen2018@foxmail.com

ABB >>

A-B>>

GE>>

BENTLY>>

TRICONEX 9783-110模塊控制器

TRICONEX 9783-110模塊控制器

TRICONEX 9783-110模塊控制器向上滑動主控制板然后將其拔下。卸下連接到主控制板的所有通信板和支架如所示。將主控制板放在防靜電袋中。備件#系列裝置系列裝置目錄號系列類型$&,'&&$$$數據銘牌位于主控制板目錄號系列標識符附近裝置上的新主控制板例如,如果的數據銘牌具有系列標識符或電流監測,新的主控制板應標有目錄號!注意:如果存在任何電壓,請移除電壓源。繼續下一步前,再次檢查電壓...

  • 功能特性
  • 參數規格
  • 視頻
  • 應用案例
  • 下載

TRICONEX 9783-110模塊控制器

    TRICONEX 9783-110模塊控制器

    向上滑動主控制板

    然后將其拔下。卸下連接到主控制板的所有通信板和支架如所示。將主控制板放在防靜電袋中。備件#系列裝置系列裝置目錄號系列類型$&,'&&$$$數據銘牌位于主控制板目錄號系列標識符附近裝置上的新主控制板例如,如果的數據銘牌具有系列標識符或電流監測,新的主控制板應標有目錄號!注意:如果存在任何電壓,請移除電壓源。繼續下一步前,再次檢查電壓。出版物年月?主控制板更換固件版本主控制板拆卸安裝通信板至筆記本電腦僅用于升級固件至掃描端口設備至掃描端口裝置至橋接器熱傳感器可用于用戶連接至隔離板至至柵極驅動板模擬安裝螺釘支座連接端口連接蓋出版物年月?主控制板更換固件版本安裝主控制板。戴上腕帶并將其連接到母線。

    安裝之前從主控制板上拆下的所有通信板如所示

    將所有安裝螺釘擰緊至。將主控制板向下滑動到滑動支座支座上。將主控制板安裝到安裝板上。將安裝螺釘擰緊至。將連接到主控制板。確認所有端子都牢固。如所示,連接和。結束步驟安裝主控制板后,從裝置中移除所有工具和碎屑,并固定隔間門。根據貴公司的程序和當?shù)貤l例,將舊電路板送至自動化公司進行維修或處理!注意:操作裝置前必須配置參數。請參閱出版物的啟動章節,以配置新主控制板中的參數。

    Slide the main control board up

    Then pull it off. Remove all communication boards and brackets connected to the main control board as shown in. Place the main control board in the anti-static bag. Spare Part # Series Device Serial Device Catalog Number Series Type $&, '&&$$$$Data plate is located on the new main control panel on the device near the catalog number series identifier of the main control panel For example, if the data plate has a series identifier or current monitoring, the new main control panel should be marked with a catalog number! Note: If any voltage is present, remove the voltage source. Check the voltage again before proceeding to the next step. Publication date ? Main Control Board Replacement Firmware Version Main Control Board Removal and Installation of Communication Board to Laptop Only for Upgrading Firmware to Scan Port Device to Scan Port Device to Bridge Thermal Sensor Available for Users to Connect to Isolation Board to Grid Drive Board Analog Installation Screw Support Connection Port Connection Cover Publication Year Month ? Replace the firmware version of the main control board and install the main control board. Wear a wrist strap and connect it to the bus.

    All communication boards removed from the main control board before installation are shown in

    Tighten all mounting screws to a torque of. Slide the main control board down onto the sliding support. Install the main control board onto the mounting plate. Tighten the mounting screws to a torque of. Connect to the main control board. Verify that all terminals are secure. Connect and as shown in. At the end of the procedure, after installing the main control panel, remove all tools and debris from the unit and secure the compartment door. Send the old circuit board to the automation company for repair or disposal according to your company's procedures and local regulations! Note: The parameters must be configured before operating the device. Refer to the launch section of the publication to configure the parameters in the new main control panel.

    12.jpg

    微信圖片_20211117105524_副本.jpg



    品牌:ICS TRIPLEX

    型號:TRICONEX 9783-110 

    產地:美國

    質保:365天

    成色:全新/二手

    發貨方式:快遞發貨


圖片名 客服

在線客服 客服一號