VMIPCI-5661工控模塊機器人備件
安裝螺母
電纜0各方向調整附件直角支架#0旋轉/傾斜支架#09..8..0.08.0.90.注意事項。如果8mm鎖緊螺母上的扭矩超過0 inlb，則可能會損壞傳感器外殼。可選安裝套件0配有兩個000、一個0090鎖緊螺母、內齒星形墊圈和用于通孔安裝的螺釘/螺母。配置Sensor All ClearSight RightSight型號時，頂蓋上有一個單圈調節旋鈕。該旋鈕控制傳感器對反射器反射回的光的靈敏度。出廠默認設置為最大靈敏度。目視對準反射器上的傳感器，直到黃色輸出LED亮起亮操作模式或熄滅暗操作模式。還要驗證橙色邊緣LED是否亮起。為了確保光束居中，需要在水平和垂直平面上掃描傳感器，并確定輸出指示器在哪個位置亮起然后熄滅。將傳感器設置在兩個位置之間的中間位置。
傳感器
可見紅色光束將在反射器上可見，并可用作對準輔助。用要檢測的物體斷開光束，并檢查輸出指示燈是否打開暗操作模式。如果沒有出現這種情況，請調低靈敏度調整，直到出現這種情況。通過移除物體恢復光束，并檢查指示器是否再次關閉，橙色邊緣LED是否亮起。如果沒有出現這種情況，請增大反射器的尺寸或減小反射器與傳感器之間的距離。在某些情況下可能需要將傳感器和反射器稍微傾斜到目標中，以最小化傳感器輸出的錯誤觸發。根據要感測的透明物體的類型，可能需要具有同軸光學器件的傳感器。配件說明目錄號安裝套件0夾具式支架8ABP8嵌入式安裝適配器090現場安裝端子室引腳DC Micro 8ATSDM跳線m.ft，引腳DC Micro889DFAC跳線m/ft，引腳AC Micro 889RFAEA反射器。
Mounting nut
Cable 0 adjustment accessories in all directions Right angle bracket # 0 Rotation/tilt bracket # 09.. 8.. 0.08.0.90. Precautions. If the torque on the 8mm locknut exceeds 0 inlb, damage to the sensor housing may occur. The optional installation kit 0 is equipped with two 000, one 0090 lock nut, internal tooth star washer and screw/nut for through hole installation. When configuring the Sensor All ClearSight RightSight model, there is a single turn adjustment knob on the top cover. This knob controls the sensitivity of the sensor to the light reflected back by the reflector. The factory default setting is maximum sensitivity. Visually align the sensor on the reflector until the yellow output LED lights up the operating mode or turns off the dark operating mode. Also verify that the orange edge LED is lit. To ensure that the beam is centered, scan the sensor in the horizontal and vertical planes and determine where the output indicator lights up and then turns off. Set the sensor midway between the two positions.
sensor
The visible red beam will be visible on the reflector and can be used as an alignment aid. Disconnect the beam with the object to be detected, and check whether the output indicator turns on the dark operation mode. If this does not happen, turn down the sensitivity adjustment until this happens. Restore the beam by removing the object and check that the indicator turns off again and that the orange edge LED lights up. If this does not happen, increase the size of the reflector or reduce the distance between the reflector and the sensor. In some cases, it may be necessary to tilt the sensor and reflector slightly into the target to minimize false triggering of the sensor output. Depending on the type of transparent object to be sensed, a sensor with coaxial optics may be required. Description of accessories Catalog No. Installation kit 0 Clamp type bracket 8ABP8 embedded installation adapter 090 Field installation terminal room pin DC Micro 8ATSDM jumper m Ft, pin DC Micro889DFAC jumper m/ft, pin AC Micro 889RFAEA reflector.
