VMIVME-3115工控模塊控制器
電源輸入
換向分解器或高分辨率輸出2.8（0.11）檢查孔（4），頂部和底部1/16至27 NPT插頭，直徑10 mm。直徑115 mm的通孔4需要。B、 C.（直徑為0.394，在直徑為4.528的BC上）安裝螺栓必須為帽頭式M6 x 1.0螺紋孔16（0.63），最小深度6.07/5.99（0.239/0.236）15.49/15.24（0.610/0.600）軸詳圖30.7（1.21）全深度端銑鍵槽1電機前端鐘形角半徑22.22（0.875）最大軸跳動0.04（0.0016）T.I.R軸端隙0.127（0.005）最大導向偏心0.08（0.0032）T.I.L最大端面跳動0.08（0.0032）T.I.R銘牌詳圖軸和導向公差高分辨率電機端部1法蘭安裝（單位：毫米和（英寸）反饋目錄編號描述AD AG C鍵端銑鍵槽（全深度）無制動器
制動器
（IP67等級），AD、AG和C增加45 mm（1.75 in.）。尺寸符合NEMA標準MG 7-2.4.1.3和IEC 72-1。軸公差符合DIN 42955，“N”公差。1326AB 460V，扭矩增強系列，交流伺服電機19出版物 扭矩增強系列（分解器和高分辨率反饋）AD AG C 50（1.97）鍵45 45 163.6最大值（6.44）25.4（1.00）25.4（1.00）25.4（1.00）130.014/129.989直徑。（5.1186/5.1176直徑）24.009/23.996直徑。（0.9452/0.9447）3.5（0.138）15.0（0.59）9.52/9.50直徑。（0.3750/0.3745直徑）130.20/30.15直徑。（5.126/5.24直徑）功率輸入2.0（0.079）8.08/8.00（0.318/0.315）19.99/19.74（0.787/0.777）軸詳圖12 mm直徑。165 mm直徑上需要通孔4。B、 C.（6.496直徑B.C.上的0.472直徑）安裝螺栓必須為帽頭式檢查孔（4），頂部和底部1/16至27 NPT堵頭M8 x 1.25螺紋孔19（0.75）深最小41（1.61）
Power input
Reversing resolver or high-resolution output 2.8 (0.11) inspection hole (4), top and bottom 1/16 to 27 NPT plugs, 10 mm diameter. Required for 115 mm diameter through hole 4. B. C. (0.394 diameter, on BC with 4.528 diameter) The mounting bolt must be a cap type M6 x 1.0 threaded hole 16 (0.63), Minimum depth 6.07/5.99 (0.239/0.236) 15.49/15.24 (0.610/0.600) shaft detail 30.7 (1.21) full depth end milling keyway 1 motor front end bell angle radius 22.22 (0.875) maximum shaft runout 0.04 (0.0016) T.I.R shaft end clearance 0.127 (0.005) maximum guide eccentricity 0.08 (0.0032) T.I.L maximum face runout 0.08 (0.0032) T.I.R nameplate detail shaft and guide tolerance high resolution motor end 1 flange installation (unit: mm and (inch) Feedback catalog number description AD AG C key end milling keyway (full depth) without brake
Brake
(IP67 grade), AD, AG and C increase by 45 mm (1.75 in.). Dimensions conform to NEMA standard MG 7-2.4.1.3 and IEC 72-1. Shaft tolerance according to DIN 42955, "N" tolerance. 1326AB 460V, torque enhancement series, AC servo motor 19 Publication torque enhancement series (resolver and high-resolution feedback) AD AG C 50 (1.97) key 45 45 163.6 maximum value (6.44) 25.4 (1.00) 25.4 (1.00) 25.4 (1.00) 130.014/129.989 diameter. (5.1186/5.1176 dia.) 24.009/23.996 dia. (0.9452/0.9447) 3.5 (0.138) 15.0 (0.59) 9.52/9.50 diameter. (0.3750/0.3745 diameter) 130.20/30.15 diameter. (5.126/5.24 diameter) power input 2.0 (0.079) 8.08/8.00 (0.318/0.315) 19.99/19.74 (0.787/0.777) shaft detail 12 mm diameter. A through-hole 4 is required on a 165 mm diameter. B. C. (0.472 diameter on 6.496 diameter B.C.) The mounting bolt must be a cap type inspection hole (4), 1/16 to 27 NPT plug M8 x 1.25 threaded hole 19 (0.75) at the top and bottom with a minimum depth of 41 (1.61)
