VMIVME-3122-013000工控模塊系統備件
電壓下測試電機
在40°C（104°F）環境中，在460V AC的線路電壓下測試電機。外殼溫度約為100°C（212°F），電機繞組比環境溫度升高80°C（176°F）。當電機安裝在304.8 mm x 304.8 mm×25.4 mm（12 in.x 12 in.x 1 in.）鋼安裝支架上時，確定扭矩額定值。電機包含兩個串聯的熱開關，在超溫條件下打開。溫度設置為155°C（311°F）±10%。觸點的額定值為115V AC時為1A，24V DC時為1A。下面顯示的所有值的公差為±10%。類別參數環境溫度單位1326AB-B720F 1326AB-B430E一般連續失速扭矩-40°C（104°F）時的AM50/75 N-m（lb in。)38（336）/56（495）56.8（502）/85.4（756）持續失速電流-40°C（104°F）時的AM50/75安培27.5/27.5 22.8/22.8峰值失速電流-30°C（106°F）下的AM50/75%安培33.2/50 33.2/50 40°C時的機械時間常數6.6 6.9 40°C下的電氣時間常數9.5 11.92額定轉速-40°F（104°C）時的460V/380V rpm 5000/4100 3350/2800熱最高環境溫度（無降額）℃40 40絕緣等級H H熱時間常數分鐘60 60 25°C（77°F）N-m（lb in。)/A 1.37（12.12）2.01（17.8）25°C（77°F）伏/1000 rpm時的電壓常數RMS（L-L）82.8 126.2 25°C）77°F時的終端電阻歐姆（L-L。)0.0127（0.0005）0.0127。
電機轉速額定運行
rpm=電機轉速額定運行間歇運行380V扭矩下的額定轉速（N-m）1326AB–B720F電機轉速（rpm）扭矩（N-m。AM75 1326AB 460V，Torque Plus系列，交流伺服電機17出版物1326A-2.9-1999年3月圖9 1326AB-B740C和1326AB-B440E旋轉變壓器和高分辨率電機的電機速度-扭矩曲線重要：所示曲線和性能數據適用于放大器額定值大于或等于電機持續失速電流的電機和1394組合。在40°C（104°F）環境中，在460V AC的線路電壓下測試電機。外殼溫度約為100°C（212°F），電機繞組比環境溫度升高80°C（176°F）。當電機安裝在304.8 mm x 304.8 mm×25.4 mm（12 in.x 12 in.x 1 in.）鋼安裝支架上時，確定扭矩額定值。電機包含兩個串聯的熱開關，在超溫條件下打開。
Test the motor under voltage
Test the motor at 460V AC line voltage in an environment of 40 ° C (104 ° F). The enclosure temperature is about 100 ° C (212 ° F), and the motor winding temperature is 80 ° C (176 ° F) higher than the ambient temperature. When the motor is mounted at 304.8 mm x 304.8 mm × Determine the torque rating when mounting on a 25.4 mm (12 in. x 12 in. x 1 in.) steel mounting bracket. The motor contains two thermal switches in series, which open under overtemperature conditions. The temperature is set to 155 ° C (311 ° F) ± 10%. The rating of the contacts is 1A at 115V AC and 1A at 24V DC. All values shown below have a tolerance of ± 10%. Category Parameter Ambient Temperature Unit 1326AB-B720F 1326AB-B430E AM50/75 N-m (lb in) at - 40 ° C (104 ° F) general continuous stall torque 38 (336)/56 (495) 56.8 (502)/85.4 (756) AM50/75 amperes at - 40 ° C (104 ° F) 27.5/27.5 22.8/22.8 AM50/75 amperes at - 30 ° C (106 ° F) peak stall current 33.2/50 33.2/50 mechanical time constant at 40 ° C 6.6 6.9 Electrical time constant at 40 ° C 9.5 11.92 460V/380V rpm at - 40 ° F (104 ° C) 5000/4100 3350/2800 thermal maximum ambient temperature (no derating) ℃ 40 40 Insulation grade H H Thermal time constant minute 60 60 25 ° C (77 ° F) N-m (lb in.)/ A 1.37 (12.12) 2.01 (17.8) RMS (L-L) voltage constant at 25 ° C (77 ° F) V/1000 rpm 82.8 126.2 25 ° C) Terminal resistance ohm at 77 ° F (L-L) 0.0127（0.0005）0.0127。
Rated operation of motor speed
rpm=rated speed (N-m) of motor under rated running intermittent running 380V torque 1326AB – B720F motor speed (rpm) torque (N-m. AM75 1326AB 460V, Torque Plus series, AC servo motor 17 publication 1326A-2.9-1999 March Figure 9 1326AB-B740C and 1326AB-B440E Motor speed torque curves for resolvers and high-resolution motors Important: The curves and performance data shown are applicable to motors with amplifier ratings greater than or equal to the motor's continuous stall current and 1394 combinations. Test the motor at 460V AC line voltage in an environment of 40 ° C (104 ° F). The enclosure temperature is about 100 ° C (212 ° F), and the motor winding temperature is 80 ° C (176 ° F) higher than the ambient temperature. When the motor is mounted at 304.8 mm x 304.8 mm × Determine the torque rating when mounting on a 25.4 mm (12 in. x 12 in. x 1 in.) steel mounting bracket. The motor contains two thermal switches in series, which open under overtemperature conditions.
