VMIVME-4132-010系統備件
針板旨在與驅動器一起
使用但可用于具有最低要求的非應用。安裝在驅動器上的轉接板尺寸產品目錄號和 這些轉接板適用于需要… 轉換器用于控制電源的應用中的驅動器產品目錄編號 和。針板旨在與驅動器一起使用但可用于具有最低要求的非應用。驅動器安裝的轉接板尺寸產品目錄號和 重要信息：由于連接接口電纜時的空間限制連接到 接口驅動器時需要。重要信息：當連接到 驅動器時請勿使用。? 尺寸單位為針連接器顯示為無蓋 針連接件顯示為不帶蓋 ?。針連接器顯示為無蓋 針接頭顯示為不帶蓋出版物年月發行說明 產品目錄號固件版本的增強功能此版本固件中沒有增強功能。糾正的異常這些糾正適用于固件版本更高版本：和編碼器支持已糾正以在同一方向上移動數千圈后通過電源循環保持絕對位置。
數字伺服驅動器
有關先前的固件更正請參閱這些出版物：數字伺服驅動器 固件版本出版物 出版物年月 固件發行說明限制當 與 伺服模塊和 驅動器一起使用時這些限制適用。不支持窗口注冊。如果指令中啟用了窗口注冊則指令將無法完成。不支持摩擦扭矩補償和齒隙補償。調整手動調整屏幕的偏移選項卡中的值將無效。傅固件版本可能支持此參數因此設置應保持默認值%。不支持速度下降。調整自定義增益屬性屏幕中的值不會產生任何影響。不支持在軸屬性屏幕的驅動選項卡中訪問的以下實時軸信息屬性：使用雙回路配置時軸屬性對話框的電機反饋和輔助反饋選項卡上的分辨率單位設置轉英寸毫米必須相同。在驅動參數的之后在設置位之后至少等待毫秒然后再對設置結果進行操
The needle plate is designed to work with the drive
Use but can be used for non applications with minimum requirements. The size of the docking stations installed on the drives Catalog numbers and these docking stations are applicable to the drive catalog numbers and in applications where... converters are used to control power. The needle plate is intended for use with drives but can be used for non applications with minimum requirements. Size of adapter plate installed on the drive Catalog number and important information: required when connecting to the interface drive due to space limitations when connecting the interface cable. Important: Do not use when connected to the drive. ? The dimension unit is the pin connector, which is displayed as a pin connector without a cover, which is displayed as a pin connector without a cover. Pin connectors are displayed as uncovered pin connectors are displayed as uncovered publications Monthly Release Notes Catalog Number Firmware Version Enhancements There are no enhancements in this version of firmware. Corrected exceptions These corrections apply to later firmware versions: and encoder support have been corrected to move thousands of cycles in the same direction to maintain absolute position through power cycles.
Digital servo driver
Refer to these publications for previous firmware corrections: Digital Servo Drive Firmware Versions Publications Monthly Firmware Release Notes Limitations These restrictions apply when used with servo modules and drives. Window registration is not supported. If window registration is enabled in a directive, the directive cannot be completed. Friction torque compensation and backlash compensation are not supported. Adjust The values in the Offset tab of the Manual Adjustment screen will not be valid. The firmware version may support this parameter, so the setting should remain at the default value of%. Speed droop is not supported. Adjusting the values in the Custom Gain Attributes screen has no effect. The following real-time axis information properties accessed in the Drive tab of the Axis Properties screen are not supported: The resolution unit settings in inches and millimeters on the Motor Feedback and Auxiliary Feedback tabs of the Axis Properties dialog box must be the same when using a dual circuit configuration. Wait for at least milliseconds after setting the bit after driving the parameter, and then operate on the setting result. Position internal error acceleration.作。位置內部誤差加速度。
