VMIVME-6016工控模塊系統備件
周圍編織
其他電纜之間或周圍編織。?在電纜之間留出至少10%的間隙，以便它們能夠自由移動。在電纜之間使用分離器。?電纜必須能夠在托架內自由移動。請勿將電纜連接到托架或彼此。將電纜夾在托架端部之外。夾緊前，將托架循環幾次。?將較重的電纜夾向軌道邊緣，將較輕的電纜夾在軌道中心。?不要將電纜緊緊拉在內側/外側軌道彎道上。隔板連接器組件下圖顯示了隔板連接器的側視圖，該連接器通過螺釘連接，并突出穿過法蘭和導電壁（如金屬柜）。前視圖顯示了連接的隔板連接器的引腳穿過墻壁。AB配對導電（金屬）壁連接器二次成型外形，黑色pvc B ED C 18-1 I A G F J H前視圖側視圖17出版物1326A-2.11-1998年5月通過機柜壁安裝隔板
安裝隔板連接器準備機柜壁：
1.確定將安裝隔板連接器的機柜壁區域。2.標記四個安裝孔和中心連接器開口的位置。3.鉆四個安裝孔和大中心開口。4.從1326-CPB1-E-xxx、1326-CPB1T-E-xxx、1326-CPR1-E-xxx或1326-CPC1T-E-xxx電纜的隔板法蘭將接觸的機柜壁內表面刮去任何油漆。注：所有B系列電纜連接器都經過黑色、高導電性鈷涂層處理。不要刮擦涂層。重要提示：金屬對金屬連接必須符合CE合規標準。5.從1326 CCU EL xxx、1326-CPB1-EL-xxx和1326-CPC1-EL-xxx電纜的連接器表面上拆下viton密封，為機柜壁提供間隙。機柜壁的連接應為IP65。6.將隔板連接器穿過墻壁，如圖所示：！注意：為避免電擊危險，在安裝或拆除電纜之前，應切斷電機控制器和電機的電源。否則可能導致人身傷害。
Weaving around
Braiding between or around other cables. ? Leave at least 10% clearance between cables so that they can move freely. Use separators between cables. ? The cable must be able to move freely in the tray. Do not connect the cables to the tray or to each other. Clamp the cable out of the end of the tray. Cycle the bracket several times before clamping. ? Clamp the heavier cable to the edge of the track and the lighter cable to the center of the track. ? Do not pull the cable tightly on the inner/outer track curve. The following figure of the bulkhead connector assembly shows a side view of the bulkhead connector, which is connected by screws and protrudes through flanges and conductive walls (such as metal cabinets). The front view shows the connected bulkhead connector pins through the wall. AB paired conductive (metal) wall connector secondary molding shape, black pvc B ED C 18-1 I A G F J H front view side view 17 publication 1326A-2.11-May 1998, partition was installed through cabinet wall
Install the bulkhead connector Prepare the cabinet wall:
1. Determine the cabinet wall area where the bulkhead connector will be installed. 2. Mark the position of four mounting holes and central connector opening. 3. Drill four mounting holes and large center openings. 4. Scrape off any paint from the partition flange of 1326-CPB1-E-xxx, 1326-CPB1T-E-xxx, 1326-CPR1-E-xxx or 1326-CPC1T-E-xxx cable on the inner surface of the cabinet wall. Note: All B series cable connectors are coated with black, high conductivity cobalt. Do not scratch the coating. Important: Metal to metal connections must comply with CE compliance standards. 5. Remove the viton seal from the connector surface of the 1326 CCU EL xxx, 1326-CPB1-EL-xxx and 1326-CPC1-EL-xxx cables to provide clearance for the cabinet wall. The connection of cabinet wall shall be IP65. 6. Pass the bulkhead connector through the wall, as shown in the figure:! Note: To avoid the risk of electric shock, cut off the power supply of the motor controller and motor before installing or removing the cable. Failure to do so may result in personal injury.
