VMIVME-7455-30工控機器人備件
遠程隔板連接
伺服電機（460V）通過導電（金屬）壁可選安裝最大寬度4.623 mm（0.182 in）1326-CCUx-D（反饋）和1326-CPB1-D/-CPC1-D（電源）1326--CUx-E（反饋）或1326-CPB1-E/-CPC1-E（電源）AB 1394 ALLEN-BRADLY AB ALLEN-BRADLEY AB1326Ax電機（460V）支架安裝（未提供）最大寬度4.623 mm（0.182 in）1326-CCUx-D（反饋）和1326-CPB1-D/-CPC1-D（電源）1326--CUx-E（反饋）或1326-CPB1-E/-CPC1-E（電源）7出版物1326A-2.11-1998年5月惡劣環境連接在惡劣環境中使用IP67電纜（帶-L選項）和L電機。圖4惡劣環境連接連接雙端隔板在線連接此解決方案將柔性電纜和非柔性電纜結合在一起，以實現單次運行。
單電纜線路中
兩個斷開連接，帶有雙端隔板、雙端標準電纜和標準電纜。圖5標準雙端艙壁，和雙端電纜，用于與 IP67伺服電機 （解析器反饋） （未提供，最大寬度4.623 mm（0.182 in）8出版物1326A-2.11-1998年5月線性彎曲定義為單向彎曲。額定彎曲電纜不適用于雙向彎曲的扭轉彎曲。不得在扭轉應用中使用電力軌道（線性撓性）電纜。用于換向的標準Allen-Bradley電纜-1326-CU-xxx和用于電源的1326-CPB1-xxx或1326-CPC1-xxx為托盤額定（固定）電纜，只能用于一次性撓性應用。?在發生動態線性彎曲的應用中，需要電力軌道布線。在這些應用中使用以下電纜：?1326 CCUT xxx（所有電機的換向）?1326-CPB1T-xxx（1326AS-B3xxx和1326AS-B4xxx電機的電源）?1326-CPC1T-xxx（用于1326AS-B6xxx和1326A S-B8xxx電機的功率）Allen-Bradley高柔電纜具有優異的最小彎曲半徑規格，在線性彎曲應用中具有較長的彎曲循環壽命。線性柔性電纜的循環壽命與電纜在電力軌道中的彎曲半徑直接相關。有關彎曲半徑與循環壽命規格，請參閱下頁的圖表。
Remote bulkhead connection
Servo motor (460V) can be optionally installed through conductive (metal) wall with a maximum width of 4.623 mm (0.182 in) 1326-CCUx-D (feedback) and 1326-CPB1-D/- CPC1-D (power supply) 1326-CUx-E (feedback) or 1326-CPB1-E/- CPC1-E (power supply) AB 1394 ALLEN-BRADLY AB ALLEN-BRADLEY AB1326Ax Motor (460V) bracket installation (not provided) with a maximum width of 4.623 mm (0.182 in) 1326-CCUx-D (feedback) and 1326-CPB1-D/- CPC1-D (power supply) 1326-CUx-E (feedback) or 1326-CPB1-E/- CPC1-E (power supply) 7 publication 1326A-2.11-May 1998 Severe environment connection IP67 cable (with - L option) and L motor were used in severe environment. Figure 4 Severe environment connection Double end bulkhead online connection This solution combines flexible and non flexible cables to achieve single operation.
In single cable route
Two disconnected connections with double ended bulkhead, double ended standard cable and standard cable. Figure 5 Standard double ended bulkhead, and double ended cable, used with IP67 servo motor (resolver feedback) (not provided, maximum width 4.623 mm (0.182 in) 8 Publication 1326A-2.11-May 1998 Linear bending is defined as one-way bending. The rated bending cable is not suitable for torsional bending of two-way bending. Power track (linear flexible) cables shall not be used in torsional applications. The standard Allen Bradley cable-1326-CU-xxx for commutation and 1326-CPB1-xxx or 1326-CPC1-xxx for power supply are tray rated (fixed) cables and can only be used for one-time flexible applications. ? In the application of dynamic linear bending, power track wiring is required. The following cables are used in these applications: ? 1326 CCUT xxx (commutation of all motors) ? 1326-CPB1T-xxx (power supply for 1326AS-B3xxx and 1326AS-B4xxx motors) ? 1326-CPC1T-xxx (power for 1326AS-B6xxx and 1326A S-B8xxx motors) Allen Bradley high flexible cables have an excellent minimum bending radius specification and a long bending cycle life in linear bending applications. The cycle life of a linear flexible cable is directly related to the bending radius of the cable in the power track. Refer to the chart on the next page for bending radius and cycle life specifications.
