VMIVME-7750-456-S2機器人模塊
麥克風輸入使用
運算放大器將嵌入式麥克風連接到音頻前置放大器通過使用和跳線設置增益；兩者必須同時設置或刪除通過修改跳線位置您可以選擇以下每個增益值： （默認設置和均關閉） （和均打開）注：系列歐姆電阻器是為未來阻抗適應設施預留的在特定的放大器設置條件下這允許在音頻路徑上輕松插入電容器或任何其他雙極器件另一方面是一個默認的歐姆電阻器它允許將從音頻輸入路徑斷開以供自定義使用音頻預放大器由專用低壓差調節器 麥克風輸入耳機輸出評估套件支持由連接到微控制器兩個通道的音頻放大器驅動的單聲道/立體聲音頻播放是一款單橋連接負載放大器設計用于驅動低至歐姆阻抗的揚聲器該放大器可以動態重新配置以將兩個立體聲單端信號驅動到耳機中
耳機輸出
和應一起設置或移除 電話插孔立體聲 評估套件硬件開發板用戶指南 ––年月日使用現成的/英寸（ ）立體聲耳機插孔當未插入插頭時控制開關關閉閉合時 /分壓器將/輸入拉低插入插孔插頭后電阻器斷開/輸入被拉高單聲道揚聲器（連接器）也與/輸出物理斷開因此在插入耳機時揚聲器不會發出聲音 設備 端口符合通用串行總線版全速設備規范是設備的微型型插座歐姆電阻器和與全速通道驅動器的（嵌入式）歐姆輸出阻抗一起建立歐姆差分阻抗和從建立分頻器橋通過實現插件檢測（電平降低到兼容的電平）圖 模擬接口模擬參考電壓參考基于（精密微功率分流電壓參考
Microphone input using
The operational amplifier connects the embedded microphone to the audio preamplifier to set the gain by using and jumpers; Both must be set or deleted at the same time You can select each of the following gain values by modifying the jumper position: (default setting and both are off) (and both are on) Note: The series ohmic resistor is reserved for future impedance adaptation facilities. Under specific amplifier setting conditions, this allows easy insertion of capacitors or any other bipolar devices on the audio path. On the other hand, it is a default ohmic resistor that allows disconnection from the audio input path for custom use. The audio preamplifier is supported by a dedicated low dropout regulator, microphone input, headphone output, evaluation kit, and connected to the microcontroller Two channel audio amplifier driven mono/stereo audio playback is a single bridge connected load amplifier designed to drive speakers with low to ohmic impedance This amplifier can be dynamically reconfigured to drive two stereo single ended signals into headphones
headphone output
And should be set or removed together Telephone jack Stereo evaluation kit Hardware development board User's Guide – – MM/DD/YYYY Use the ready-made/inch () stereo headphone jack When the plug is not inserted, the control switch is closed/the voltage divider pulls/the input is pulled down When the plug is inserted into the jack, the resistor is disconnected/the input is pulled up Mono speaker (connector) It is also physically disconnected from the/output so that the speaker will not emit sound when the headset is plugged in. The device port complies with the Universal Serial Bus version of the full speed device specification. The device's miniature socket ohmic resistor and the (embedded) ohmic output impedance together with the full speed channel driver establish the ohmic differential impedance and detect through the implementation plug-in from the establishment of the frequency divider bridge (the level is reduced to a compatible level) Figure Analog interface analog reference voltage reference is based on (precision micro power shunt voltage reference
