模塊IS200VTCCH1C
安裝閃存套件
1.從Allen Bradley Web Updates網站安裝20-COMM-E適配器的閃存套件實用程序。（這也會自動安裝最新版本的ControlFLASH實用程序，并在您的計算機上部署用于HyperTerminal的固件文件。）2.您現在可以使用DriveExplorer、DriveExecutive、ControlFLASH或HyperTermination來更新適配器。請參閱下面的相應章節并按照說明進行操作。步驟3步驟2步驟4！注意：存在永久性設備損壞的風險。啟動閃存更新后，在下載完成且適配器MOD狀態指示燈開始閃爍綠色之前，請勿斷開驅動器（或20-XCOMM-DC-BASE外部通信套件，如果使用）的電源。如果在此之前斷電，適配器可能會永久損壞。以這種方式損壞的適配器無法修理。6 20-COMM-E EtherNet/IP適配器固件v4.001使用DriveExplorer Lite/Full 1.安裝閃存套件（請參閱第5頁的安裝閃存套件）后，連接到適配器的驅動器聯機
啟動DriveExplorer并使用連接到適配器的驅動器聯機（僅使用DriveExplorer Full或1203-USB或1203-SSS轉換器通過EtherNet/IP）。
2.在DriveExplorer樹視圖中，單擊20-COMM-E適配器。然后單擊信息圖標，如圖1所示，以顯示適配器的Properties屏幕。3.在20-COMM-E屬性屏幕上，單擊詳細信息選項卡。
Installing the flash kit
1. Install the flash kit utility for the 20-COMM-E adapter from the Allen Bradley Web Updates website. (This will also automatically install the latest version of ControlFLASH utility and deploy the firmware file for HyperTerminal on your computer.) 2. You can now use DriveExplorer, DriveExecutive, ControlFLASH or HyperTermination to update the adapter. Refer to the appropriate sections below and follow the instructions. Step 3 Step 2 Step 4! Note: There is a risk of permanent equipment damage. After starting the flash update, do not disconnect the power supply of the drive (or 20-XCOMM-DC-BASE external communication kit, if used) until the download is complete and the adapter MOD status indicator starts flashing green. If power is lost before this, the adapter may be permanently damaged. An adapter that is damaged in this way cannot be repaired. 6 20-COMM-E EtherNet/IP Adapter Firmware v4.001 Using DriveExplorer Lite/Full 1. After installing the flash kit (see Installing the flash kit on page 5), the drive connected to the adapter comes online
Start DriveExplorer and go online using the drive connected to the adapter (via EtherNet/IP using DriveExplorer Full or 1203-USB or 1203-SSS converters only).
2. In the DriveExplorer tree view, click 20-COMM-E adapter. Then click the information icon, as shown in Figure 1, to display the Properties screen of the adapter. 3. On the 20-COMM-E Properties screen, click the Details tab.
