国产精品久久二区二区,熟女少妇内射日韩亚洲,久久亚洲国产成人精品无码区,GOGO熟女少妇大尺度

您的瀏覽器版本過低,為保證更佳的瀏覽體驗,請點擊更新高版本瀏覽器

以后再說X

歡迎訪問瑞昌明盛自動化設備有限公司網站!

圖片名

全國訂購熱線:
+86 15270269218E-mail:xiamen2018@foxmail.com

主頁 > 產品中心 > HONEYWELL

HONEYWELL

ABB >>

A-B>>

GE>>

BENTLY>>

Honeywell 05701-A-0325工控備件機器人模塊

Honeywell 05701-A-0325工控備件機器人模塊

Honeywell 05701-A-0325工控備件機器人模塊數據銘牌位于主控制板附近目錄號系列標識符新主裝置上的控制板例如,如果RGU的數據銘牌具有B系列標識符(或 CT電流監測),則新的主控制板應標有目錄號-PMA!注意:如果存在任何電壓,請拆下電壓源。繼續下一步前,再次檢查電壓。出版物F- 年月日RGU? 主控制板更換固件版本圖主控制板圖拆卸安裝通信板 至筆記本電腦(僅用于升級固件)至CAN...

  • 功能特性
  • 參數規格
  • 視頻
  • 應用案例
  • 下載

Honeywell 05701-A-0325工控備件機器人模塊

    Honeywell 05701-A-0325工控備件機器人模塊

    數據銘牌

    位于主控制板附近目錄號系列標識符新主裝置上的控制板例如,如果RGU的數據銘牌具有B系列標識符(或 CT電流監測),則新的主控制板應標有目錄號-PMA!注意:如果存在任何電壓,請拆下電壓源。繼續下一步前,再次檢查電壓。出版物F- 年月日RGU? 主控制板更換固件版本圖主控制板圖拆卸安裝通信板 至筆記本電腦(僅用于升級固件)至CANport設備至CANport設備至NTC橋接熱傳感器可用于用戶連接至隔離板(J)至TE至柵極驅動器板(J)(模擬IO)安裝螺釘支架連接端口連接蓋出版物F- 年月RGU? 主控制板更換固件版本 安裝主控制板戴上ED腕帶并將其連接到PE母線。

     安裝螺釘擰緊

    安裝之前從主控制板上拆下的所有通信板(如圖所示)。將所有安裝螺釘擰緊至 lb in( N-m)。將主控制板向下滑動到滑動安裝支架上。將主控制板安裝到安裝板上。將安裝螺釘擰緊至 lb in( N-m)。將TB連接到主控制板。確認所有端子牢固。連接J、J、J、J、J和J,如圖所示。結束步驟安裝主控制板后,從裝置上移除所有工具和碎屑,并固定隔間門。將舊電路板送至自動化公司進行維修或根據貴公司的程序和當地條例處理電路板!注意:操作裝置前必須配置參數。請參閱出版物F-的啟動章節,以配置新主控制板中的參數。出版物F- 年月PN 取代出版物F--年月版權所有年國際公司。

    Data plate

    For example, if the data nameplate of the RGU has the B series identifier (or CT current monitoring), the new main control panel should be marked with the catalog number PMA! NOTE: If any voltage is present, remove the voltage source. Check the voltage again before proceeding to the next step. Publication F - Year Month Day RGU ?  Main Control Board Firmware Replacement Version Diagram Main Control Board Diagram Removing and Installing Communication Board to Laptop (Only for Firmware Upgrade) to CANport Device to CANport Device to NTC Bridging Thermal Sensor for Users to Connect to Isolation Board (J) to TE to Grid Driver Board (J) (Analog IO) Mounting Screw Bracket Connection Port Connection Cover Publication F - Month RGU ?  Replace the firmware version of the main control board Install the main control board, put on the ED wrist strap and connect it to the PE bus.

    Tighten the mounting screws

    Install all communication boards removed from the main control board before installation (as shown in the figure). Tighten all mounting screws to lb in (N-m). Slide the main control board down onto the sliding mounting bracket. Install the main control board onto the mounting plate. Tighten the mounting screws to lb in (N-m). Connect the TB to the main control board. Verify that all terminals are secure. Connect J, J, J, J, J, and J as shown. At the end of the procedure, after installing the main control panel, remove all tools and debris from the unit and secure the compartment door. Send the old circuit board to the automation company for repair or dispose of the circuit board according to your company's procedures and local regulations! Note: The parameters must be configured before operating the device. Refer to the Startup section of publication F - to configure the parameters in the new main control panel. Publication F - Year PN supersedes Publication F - Year Copyright International Corporation.

    23.jpg

    20.jpg

    21.jpg

    16.jpg



    品牌:Honeywell 

    型號:05701-A-0325 

    產地:瑞士

    質保:365天

    成色:全新/二手

    發貨方式:快遞發貨



圖片名 客服

在線客服 客服一號