MVME5500工控模塊機器人備件
繼續下一步前，再次檢查電壓。
隔離板更換圖1 RGU隔離板表A：負載電阻器套件電流電壓系列代碼位于主控制板附近的典型RGU銘牌例如，此銘牌顯示電流代碼L和電壓代碼C。合適的套件為2364-SDP06A。由于銘牌顯示這是一個a系列裝置，TB2中不需要電阻器。a系列B出版物2364F-5.13 1999年6月RGU? 隔離板更換5安裝隔離板1.將負載電阻器固定在新板上的端子中（驗證透明絕緣層沒有進入端子）。擰緊至6 lb in（0.7 N-m）。注：TB2僅用于B系列RGU（見數據銘牌）。2.將電路板放在六個支架上并固定電路板。3.將端子塊TB5和TB6連接至隔離板。接線板必須牢固地壓入適當?shù)牟遄小?.將反饋連接連接到J1，將帶狀電纜連接到J2，將電流傳感器連接到J7，將PE地線連接到P1。5.將Lexan防護罩更換到隔離板上。6.驗證SW1設置正確（115V AC）。結束步驟安裝隔離板后，更換所有Lexan屏蔽并固定隔間門。
將電路板送至自動化公司進行維修，或根據貴公司的程序和當?shù)貤l例處理舊電路板！注意：SW1必須設置為適當?shù)目刂乒β省W1設置為錯誤設置將導致隔離板和其他部件損壞。PN 192666取代出版物年3月版權所有1999年國際公司。在美國印刷的Lexan是通用電氣公司的商標出版物2364F-5.13 1999年6月更換套件說明RGU? 隔離板更換內容本文檔介紹了如何拆卸和更換再生直流母線電源裝置（RGU）中的隔離板和負載電阻器。此工具包包含的內容使用下表，驗證您已收到工具包中的相應項目。
Check the voltage again before proceeding to the next step.
Isolation board replacement Figure 1 RGU isolation board Table A: Load resistor kit Current voltage series code Typical RGU nameplate located near the main control board For example, this nameplate shows current code L and voltage code C. The appropriate kit is 2364-SDP06A. Since the nameplate shows that this is a series a device, no resistor is required in TB2. A Series B Publication 2364F-5.13 June 1999 RGU ? Replace the isolation board 5 Install the isolation board 1. Fix the load resistor in the terminal on the new board (verify that the transparent insulating layer does not enter the terminal). Tighten to 6 lb in (0.7 N-m). Note: TB2 is only used for B series RGUs (see data nameplate). 2. Place the circuit board on the six brackets and fix the circuit board. 3. Connect terminal blocks TB5 and TB6 to the isolation board. The terminal block must be firmly pressed into the appropriate socket. 4. Connect the feedback connection to J1, the ribbon cable to J2, the current sensor to J7, and the PE ground wire to P1. 5. Replace the Lexan shield onto the isolation plate. 6. Verify that SW1 is set correctly (115V AC). At the end of the step, replace all Lexan shields and secure the compartment door after installing the isolation panel.
Send the circuit board to the automation company for maintenance, or dispose of the old circuit board according to your company's procedures and local regulations! Note: SW1 must be set to the appropriate control power. Setting SW1 to the wrong setting will cause damage to the isolation panel and other components. PN 192666 replaces the publication March 1999 Copyright International Corporation. Lexan, printed in the United States, is a trademark publication of General Electric Company 2364F-5.13 Replacement Kit Description RGU, June 1999 ? Isolation board replacement content This document describes how to remove and replace the isolation board and load resistor in the regenerative DC bus power supply unit (RGU). Use the following table to verify that you have received the corresponding items in the toolkit.
