DS215SLCCG1AZZ01B工控機器人備件
進行安裝
按照這些說明進行安裝時，模塊安裝緊湊型I/O適用于工業環境。具體而言，本設備適用于清潔、干燥的環境（污染等級2（1））和不超過過電壓II（2）類（IEC 60664-1）的電路。（3） 防止靜電放電去除電源（1）污染等級2是一種通常只發生非導電污染的環境，但偶爾會出現冷凝引起的臨時導電性。（2） II類過電壓是配電系統的負載水平部分。在這個水平上，瞬態電壓受到控制，不會超過產品絕緣的沖擊電壓能力。（3） 污染等級2和過電壓等級II是國際電工委員會（IEC）的名稱。注意！如果接觸總線連接器引腳，靜電放電可能會損壞集成電路或半導體。處理模塊時，請遵循以下指導原則：觸摸接地物體以釋放靜電。佩戴經批準的腕帶接地裝置。請勿觸摸總線連接器或連接器引腳。請勿觸摸模塊內部的電路部件。如果可用，使用靜態安全工作站。不使用時，將模塊保持在其靜態屏蔽盒中。注意！卸下或插入此模塊之前，請先斷開電源。
卸下或插入模塊時
在通電的情況下卸下或插入模塊時，可能會發生電弧。電弧可通過以下方式造成人身傷害或財產損失：向系統的現場設備發送錯誤信號，導致機器意外移動在危險環境中引發爆炸電弧會導致模塊及其配套連接器上的觸點過度磨損。觸點磨損可能會產生電阻。緊湊型32點固態24V直流電源輸出模塊5出版物1769-IN031A-EN-P-2003年4月系統組件模塊可在安裝之前或之后連接到控制器或相鄰的I/O模塊。有關安裝說明，請參閱第6頁的面板安裝，或第8頁的DIN導軌安裝。要使用已安裝的系統，請參見第8頁更換系統中的單個模塊。以下步驟向您介紹如何組裝緊湊型I/O系統。1.斷開電源。2.檢查待安裝模塊的母線桿是否處于解鎖（完全右側）位置。3.使用上下舌槽槽（1）將模塊固定在一起（或固定在控制器上）。4.沿舌槽槽向后移動模塊，直到總線連接器（2）彼此對齊。5.將母線桿輕輕向后推，以清除定位凸耳（3）。用手指或小螺絲刀。6.為了允許控制器和模塊之間的通信，將總線桿完全向左移動（4），直到發出咔嗒聲。確保其牢固鎖定到位。注意！連接I/O模
Install
When installed according to these instructions, the module installation compact I/O is suitable for industrial environments. Specifically, this equipment is applicable to clean and dry environment (pollution level 2 (1)) and circuits not exceeding overvoltage class II (2) (IEC 60664-1). (3) Electrostatic discharge prevention and removal power supply (1) Pollution level 2 is an environment where only non-conductive pollution usually occurs, but temporary conductivity caused by condensation occasionally occurs. (2) Type II overvoltage is the load level part of the distribution system. At this level, the transient voltage is controlled and will not exceed the impulse voltage capability of the product insulation. (3) Pollution class 2 and overvoltage class II are the names of the International Electrotechnical Commission (IEC). be careful! If you touch the bus connector pins, electrostatic discharge may damage the integrated circuit or semiconductor. When handling the module, follow these guidelines: Touch a grounded object to discharge static electricity. Wear an approved wrist strap grounding device. Do not touch the bus connector or connector pins. Do not touch the circuit components inside the module. If available, use a static security workstation. When not in use, keep the module in its static shielding box. be careful! Disconnect the power supply before removing or inserting this module.
When removing or inserting a module
When removing or inserting a module with power on, arcing may occur. The electric arc can cause personal injury or property damage in the following ways: sending wrong signals to the field equipment of the system, causing accidental movement of the machine, causing explosive arc in a dangerous environment, and causing excessive wear of the contacts on the module and its mating connectors. Worn contacts can create resistance. Compact 32 point solid state 24V DC power output module 5 Publication 1769-IN031A-EN-P-April 2003 System component modules can be connected to the controller or adjacent I/O modules before or after installation. For installation instructions, refer to Panel Mounting on page 6 or DIN Rail Mounting on page 8. To use an installed system, see Replacing Individual Modules in the System on page 8. The following steps show you how to assemble a compact I/O system. 1. Disconnect the power supply. 2. Check whether the bus bar of the module to be installed is in the unlocked (full right) position. 3. Use the upper and lower tongue slots (1) to fix the modules together (or on the controller). 4. Move the module backward along the tongue slot until the bus connectors (2) are aligned with each other. 5. Push the bus bar back slightly to clear the locating lug (3). Use your fingers or a small screwdriver. 6. To allow communication between the controller and the module, move the bus bar completely to the left (4) until a click occurs. Make sure it is securely locked in place. be careful! Connecting I/O modules
