DS200TCEAG1BSF工控模塊系統備件
固件存儲
使用此閃存是可選的。閃存中的固件存儲此CPU使用非易失性閃存存儲操作系統固件。這允許在不拆卸模塊或更換EPROM的情況下更新固件。通過將PC兼容計算機連接到模塊的串行端口并運行隨附的軟件來更新操作系統固件電源（PWR724/PWR748），如下圖所示。環境溫度（）C 10 100W 10W 20W 60W 80W 90W 50W 40W 30W正常工作范圍無強制空氣循環20 30 40 50 60 55 PWR711 PWR724 PWR748 90W 60W 75W安裝OEM、系統集成商或最終用戶有責任正確安裝PLC設備，確保安全可靠運行。產品手冊提供了有關PLC設備安裝、啟動和正確使用的詳細信息。PLC編程軟件附帶的安裝手冊描述了如何正確安裝設備。
中央處理單元
96 MHz、32位、浮點、1 Mbyte內存中央處理單元GFK-1431F PLC CPU 1999年11月系列90-70可編程控制器數據表手冊GFK-0600F 20-3如果PLC安裝必須符合支持的標準，如FCC或CE指令，請參閱PLC編程軟件附帶的符合標準的安裝要求，了解更多指南。未參考適用的可編程控制器安裝手冊，不得嘗試安裝。將電池連接至模塊上的任一電池連接器（見圖2）。將撥動開關置于停止位置。將鑰匙開關置于記憶保護斷開位置。確保機架電源已關閉。將CPX 782模塊安裝在機架0的插槽1中（見圖1）。打開電源。模塊應通電，左上角（OK）LED應閃爍。診斷成功完成后，左上角的LED保持點亮，第二個（運行）和第三個（EN）LED熄滅。如果鑰匙開關處于off位置，則第四個（左下角）LED（MEM PROTECT）熄滅。
Firmware storage
The use of this flash memory is optional. Firmware storage in flash This CPU uses non-volatile flash to store operating system firmware. This allows the firmware to be updated without removing the module or replacing the EPROM. Update the operating system firmware power supply (PWR724/PWR748) by connecting a PC compatible computer to the serial port of the module and running the accompanying software, as shown in the following figure. Ambient temperature () C 10 100W 10W 20W 60W 80W 90W 50W 40W 30W No forced air circulation in normal working range 20 30 40 50 60 55 PWR711 PWR724 PWR748 90W 60W 75W Installation OEM, system integrator or end user are responsible for correctly installing PLC equipment to ensure safe and reliable operation. The product manual provides detailed information about the installation, startup and proper use of the PLC equipment. The installation manual included with the PLC programming software describes how to properly install the equipment.
Central processing unit
96 MHz, 32-bit, floating point, 1 Mbyte memory central processing unit GFK-1431F PLC CPU November 1999 Series 90-70 Programmable Controller Data Sheet Manual GFK-0600F 20-3 If the PLC installation must conform to the supported standards, such as FCC or CE instructions, please refer to the standard installation requirements attached to the PLC programming software for more guidance. Do not attempt to install without referring to the applicable PLC installation manual. Connect the battery to any battery connector on the module (see Figure 2). Place the toggle switch in the STOP position. Place the keyswitch in the memory protection OFF position. Make sure the rack is powered off. Install the CPX 782 module in slot 1 of rack 0 (see Figure 1). Turn on the power. The module should be powered and the upper left (OK) LED should flash. After successful diagnosis, the LED in the upper left corner remains on, and the second (running) and third (EN) LEDs go out. If the key switch is in the off position, the fourth (lower left) LED (MEM PROTECT) goes out.
