DS200TCDAH1BGD模塊備件
詳細規范
帶HART參數規范的模擬輸出輸出類型4-20 mA電流回路輸出通道32每個模塊1最大值（帶或不帶開路檢測）輸出紋波<125 mV，在電源線頻率下，峰值電壓250? 負載輸出溫度漂移0.001%滿量程/°C輸出回讀精度0.25%滿量程輸出電流線性度±0.05%滿量程標稱分辨率12位校準精度0.1 W閉合觸點5 kΩ>0.25 W閉合觸點檢測1.8mA<I<6 mA 1開路觸點檢測0.7 mA<I<1.8 mA 2開路線檢測I<0.7 mA輸入濾波器一階低通16 Hz注1：在24 VDC，等于8.57 KΩ>R>4 KΩ（其中R=總回路電阻）注2：24 VDC時，等于26.7 KΩ>R>10 KΩ詳細規范–無OWD參數規范的數字輸入開路電壓24 VDC閉合觸點電流7 mA±5%，開路狀態檢測3.5 mA±5%后，閉合狀態檢測后閉合觸點檢測I>2.81mA 1斷開觸點檢測I<1.8mA 2）
輸入濾波器一階低通16 Hz注
1：在24 VDC時，等于R<8.57 KΩ（其中R=總回路電阻）注2：在24 V直流時，等于26.7 KΩ>R>10 KΩExperion Series-C I/O規范，EP03-490-520 43版本1.5霍尼韋爾專有2021 12月詳細規范-數字輸出參數規范每個模塊最大32個輸出通道（帶或不帶開路檢測）4個輸出型固態電源，防短路3個負載電流0mA 1mA最小到0.5A最大每個通道2個最大9 A每個模塊1個最大通態電壓24 V（典型），負載電流@0.5A關閉狀態電壓0v VDC（最大值）關閉狀態泄漏電流<0.1 mA無切換（0ms）時輸出到現場的間隙（0電流）（僅適用于冗余）
Detailed specifications
Analog output type with HART parameter specification 4-20 mA current loop output channel 32 maximum value of each module 1 (with or without open circuit detection) output ripple<125 mV, Peak voltage 250 Ω Load output temperature drift 0.001% Full scale/° C Output back reading accuracy 0.25% Full scale output current linearity ± 0.05% Full scale nominal resolution 12 bit calibration accuracy 0.1 W Closed contact 5 k Ω>0.25 W Closed contact detection 1.8 mA<I<6 mA 1 Open contact detection 0.7 mA<I<1.8 mA 2 Open line detection I<0.7 mA Input filter First order low-pass 16 Hz Note 1: At 24 VDC, Equal to 8.57 K Ω>R>4 K Ω (where R=total loop resistance) Note 2: When 24 VDC, it is equal to 26.7 K Ω>R>10 K Ω Detailed specification – open circuit voltage of digital input without OWD parameter specification 24 VDC closed contact current 7 mA ± 5%, after open circuit status detection 3.5 mA ± 5%, closed contact detection I>2.81mA 1 open contact detection I<1.8mA 2)
Input filter 1st order low-pass 16 Hz Note
1: At 24 VDC, it is equal to R<8.57 K Ω (where R=total loop resistance) Note 2: At 24 V DC, it is equal to 26.7 K Ω>R>10 K Ω Experience Series-C I/O specification, EP03-490-520 43 version 1.5 Honeywell proprietary December 2021 detailed specification - digital output parameter specification Each module has a maximum of 32 output channels (with or without open circuit detection) 4 output solid-state power supplies, Short circuit proof 3 load currents 0mA, 1mA, minimum to 0.5A, maximum 2 per channel, maximum 9 A, each module, maximum on state voltage, 24V (typical), load current @ 0.5A, off state voltage, 0v VDC (maximum), off state leakage current<0.1 mA, no switching (0ms), clearance output to the site (0 current) (only applicable to redundancy)
