DS200TCQCG1BEF機器人模塊卡件
保護和認證
同一IOM上的其他頻道將不受影響。AI、AO和DI通道經過進一步保護和認證，可支持能量受限/非易燃現場接線連接至2區/2區危險位置。Experion Series-C輸入/輸出規范，EP03-490-520 45版本1.5霍尼韋爾專有2021 12月詳細規范-模擬輸入參數規范輸入類型電流（2、3或4線設備）輸入通道每個模塊最大32個（帶或不帶開路檢測）A/D轉換器分辨率16位輸入范圍0-20 mA或4-20 mA正常模式抑制比50 Hz時18 dB，60 Hz輸入濾波器響應時為20 dB，單極，6 Hz串擾時為-3 dB，dc至60 Hz（通道至通道）60 dB輸入阻抗250Ω輸入電壓范圍（任何參考公共輸入，無損壞）+33 VDC至-1 VDC（1）輸入掃描速率10 ms硬件精度滿標度0.1%（23.5±2°C）滿標度0.175%（0至+70°C）0.25%（-40至+70℃）短路電流限制25 mA注1：返回端子直接連接至公共（接地）詳細信息規格–脈
沖輸入參數規格信
道任何4信道頻率0-15 kHz最小脈沖寬度25μs占空比任何滿足最小脈沖寬度規格Experion Series-C I/O規格的占空比，EP03-490-520 46版本1.5霍尼韋爾專有2021 12月詳細規范-帶HART1參數規范的模擬輸出輸出輸出輸出類型4-20 mA輸出通道32最大每個模塊2輸出溫度漂移0.007%滿標度/°C輸出回讀診斷±4%滿標量輸出電流線性±0.05%滿標程（標稱）分辨率12位校準精度<0.35%滿量程（25oC），包括線性可直接設置輸出電流范圍0 mA、2.9 mA至21.1 mA最大電阻負載（24 V電源）825歐姆@20 mA最大輸出兼容電壓（24 V供電）16.5 VDC@20 mA開路電壓電源電壓（26 VDC最大）響應時間，DAC輸入代碼在HART模式下輸出（在最終值的3%以內）80 ms，在非HART模式中0.25 ms，在切換0 ms時輸出到現場的間隙（0 mA）（兩個合作伙伴持續激活）注1：如果AO通道的配置從非HART改為HART，且模擬OP保持通電，則通道重新加載時，輸出的干擾不超過65 ms。將AO通道從HART更改為非HART不會產生任何OP干擾。注2：請參考《用戶指南》，了解確定信道使用與工作溫度的計算方法。
Protection and certification
Other channels on the same IOM will not be affected. AI, AO and DI channels are further protected and certified to support energy limited/non incendive field wiring to Zone 2/Zone 2 hazardous locations. Experion Series-C input/output specification, EP03-490-520 45 version 1.5 Honeywell proprietary December 2021 detailed specification - Analog input parameter specification Input type Current (2, 3 or 4-wire device) Input channel maximum 32 per module (with or without open circuit detection) A/D converter resolution 16 bit input range 0-20 mA or 4-20 mA Normal mode rejection ratio 18 dB at 50 Hz, 20 dB at 60 Hz input filter response, - 3 dB at 6 Hz crosstalk, Dc to 60 Hz (channel to channel) 60 dB input impedance 250 Ω input voltage range (any reference to common input, no damage)+33 VDC to - 1 VDC (1) input scanning rate 10 ms Hardware accuracy Full scale 0.1% (23.5 ± 2 ° C) Full scale 0.175% (0 to+70 ° C) 0.25% (- 40 to+70 ° C) Short circuit current limit 25 mA Note 1: Return terminals are directly connected to common (ground) Details Specification – Pulse
Input parameter specification information
Channel Any 4-channel frequency 0-15 kHz Minimum pulse width 25 μ s duty cycle Any duty cycle that meets the minimum pulse width specification Experion Series-C I/O specification, EP03-490-520 46 version 1.5 Honeywell proprietary December 2021 detailed specification - Analog output with HART1 parameter specification Output type 4-20 mA Output channel 32 Maximum output temperature drift of each module 2 0.007% Full scale/° C output back reading diagnosis ± 4% Full scale output current linear ± 0.05% Full scale (nominal) resolution 12 bit calibration accuracy<0.35% Full scale (25oC), including linear output current range 0 mA 2.9 mA to 21.1 mA maximum resistive load (24 V power supply) 825 ohms @ 20 mA maximum output compatible voltage (24 V power supply) 16.5 VDC@20 The response time of the mA open circuit voltage power supply voltage (26 VDC maximum), the DAC input code output (within 3% of the final value) 80 ms in HART mode, 0.25 ms in non HART mode, and the output gap to the site (0 mA) when switching 0 ms (two partners continuously activate) Note 1: If the configuration of the AO channel is changed from non HART to HART, and the analog OP remains powered on, the output interference will not exceed 65 ms when the channel is reloaded. Changing the AO channel from HART to non HART will not cause any OP interference. Note 2: Please refer to the User's Guide for the calculation method to determine the channel use and operating temperature.
